Mark “Dr. AIX” Waldrep, the founder of AIX Records and a long-standing A8 user who has a successful live Kickstarter campaign running right now on a new book on streaming, downloaded music and personal audio has just commented in there that he will be covering HTRF technology and Smyth Research’s efforts in the area in his new book. More importantly he mentioned his studio is/was one of the best places to get a measurement in which I don’t doubt based on the sound quality of his label’s recordings. Not sure whether he offers the measurement service or not but those A8, A16 owners near LA may want to ask him perhaps.
I know that the team at Smyth Research has never produced anything ahead of or close to schedule but I am hoping(against hope?) that they are able to get the Realiser Exchange, complete with CanJam PRIRs, online by Christmas.
I know that the team at Smyth Research has never produced anything ahead of or close to schedule but I am hoping(against hope?) that they are able to get the Realiser Exchange, complete with CanJam PRIRs, online by Christmas.
For those of us with CanJam PRIRs even just getting those would be a great Christmas present. Really hope they are not lost or mixed up, it’s been a long time since they were taken.
4-6 weeks.
In Smyth weeks this means 4-6 months...
(just kidding...)
Concerning buzzes/white noise etc.: until now I had these errors only with FW 1.91. Then I downgraded to 1.81 and it was ok. Now with 1.98 so far none of these bugs. I hope it'll stay this way. So possibly (hopefully) really a FW issue.
I hope no HW issue and I don't need to send the unit back to Northern Ireland, concerning the nightmares others had with sending their units back and forth.
If we had no pandemic I'd fly over there with my Realiser in the hand luggage...
Still waiting for the new internal SD card, because I had the stalls, but so far also none of these with 1.98.
I told Stephen I'm not in a hurry because everything seems to run smooth at the moment.
Finally found time to install Apple TV 4K and listen to Tidal Dolby Atmos stuff as well as watch Netflix Films with Dolby Atmos. The 9.1.4 measurement in a recording studio paid 100% off for both. What a great experience! Thanks to calibration HD800 even has clean deep rumbling subbass.
I apologize if I missed it somewhere, but did you ever figure out what the best files were for async measurements? Meaning which is the best file for premeasurement gain calibration and all that stuff? I might have some time to take another shot at my 5.1 async capture and was curious if there were certain gain files you found to be better than other, etc.
I’ve made a simplified to-do list for resuming measurements with Realiser A16. You can see some of the settings for the A16 and angles for “look centre”.
The first six PRIRs are the ones suggested by @audiohobbit. My subwoofer is connected to the audio system via a miniDSP. Previously, when I tried to capture the PRIR for SW, I muted the two speakers, but I don't know why I couldn’t hear the sweep for the SW either. If I connected the SW to line output 3-4 of A16, set up a new preset in miniDSP only for the SW with the LPF at 120 Hz, then I could hear the sweep for the SW.
For the PRIRs corresponding to the ceiling mounted speakers, I’ll use the top of a bookcase that is roughly 2 metres height. The connections and angles are shown in the attached table.
I hope that next week a colleague from the office can assist me so that I don't have to get up from the measuring position to change the required settings in A16 and move the set-top device.
Thanks again for helpful suggestions I received in this forum.
I highly doubt the exchange will be up by Christmas at this point. Or maybe it’ll be up tomorrow. It’s hard to see where their priorities lie. New firmware, people shipping back units with issues, exchange, buyers outside of Kickstarter. They’ve 100% fallen behind on their 10 a week for Kickstarter backers. I should’ve received my shipping email at least. #329.
Finally found time to install Apple TV 4K and listen to Tidal Dolby Atmos stuff as well as watch Netflix Films with Dolby Atmos. The 9.1.4 measurement in a recording studio paid 100% off for both. What a great experience! Thanks to calibration HD800 even has clean deep rumbling subbass.
Finally found time to install Apple TV 4K and listen to Tidal Dolby Atmos stuff as well as watch Netflix Films with Dolby Atmos. The 9.1.4 measurement in a recording studio paid 100% off for both. What a great experience! Thanks to calibration HD800 even has clean deep rumbling subbass.
Yes, this magic device NEEDS more reviews and attention. But I’m afraid I agree that it’s a very difficult device to learn and it’s perfection is very elusive.
Just watch Zeos unboxing. He’s a very experienced YouTube reviewer and although brash and shouty, he’s very knowledgeable. I’m not sure he’s review will be positive. We’ll see.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.