[The Monkey]

very cool, ttr!

 

[Nisbeth]

Birch plywood? Very original for someone from Finland

/U.


Seriously, that's very nice work ttr

 

[ttr]

Quote:

Originally Posted by Nisbeth Birch plywood? Very original for someone from Finland

Touche

Thanks!

 

[Twombly]

Is the CMoy-in-a-wood-enclosure-with-a-pretty volume knob a coquettish jab at the RA-1?

 

[saab]

Thought I would put up the Millet Hybrid I am finishing. All I have left to do is get the AC socket permantly installed in the back of the power supply box (it is hanging out like a little tail.)

Here is the amp sitting on the power supply.

Just the amp

Glamour tube shot

I sounds wonderful. It is too bad that I already have it traded.

-John

 

[Oink1]

Nice work saab - I think you should stain/varnish the exposed wood in the lid where the tube holes are

 

[strogg]

Cmoy-in-women's-deodorant!:

It uses an OPA4227PA as the opamp. the reason why i used a 4 channel rather than the 2 channel is to utilize one of the channels as sort of a buffer for the rail splitter (rather than using the TLE). it works very well and sounds pretty nice. Best of all, it fits perfectly in one of them portable deodorant packs stacked on top of 2 9v batteries

the wires coming out are the in-line input and output jacks. one is a neutrik 1/4" in-line jack and the other is a 1/8" neutrik male connector. the white cable is a starquad with a strain relief inside that i made with hot-glue and a ziptie (hot glue gluing on the zip tie that's wrapped around the wire).

 

[Lavalamp]

Cmoy-in-women's-deodorant!:

Would you describe this amp as clean sounding?

 

[rreynol]

Definately do not try to board a plane with that cmoy.

 

[chillysalsa]

Please tell me, does the thumb-wheel to dispense deodorant act as the volume knob???

 

[strogg]

Quote:

Originally Posted by rreynol Definately do not try to board a plane with that cmoy.

I'll make sure to put some more frayed wires first

Quote:

Originally Posted by chillysalsa Please tell me, does the thumb-wheel to dispense deodorant act as the volume knob???

it dispenses great sound

seriously, i was going to do that, but there is no pot small enough or flat enough to fit in there

 

[GuffMorgan]

Strong enough for a Senn, but made for a Grado?

Edit:
I'm sorry, I'm sorry, that was really really bad

 

[blueworm]

Just finished millet Hybrid (sitting on a pimeta with a steps to its right.)

 

[till]

This is a CMoy in a blue translucent Hammond case:
blue CMoy
The 9 V battery slider is made by Bulgin; the amp also has a DC plug. The opamp is socketed (OPA2227). The ground channel contains a TLE2426 and a BUF634 in a TO220 case through which I stuck the blue LED. The circuit (straight from Headwize, gain of 5.5, with Meier bass-enhanced crossfeed after the input jack) was soldered on breadboard. The caps are 1500 µF Nichicon PF(M). The pot is an Alps RK097 from Tangent. The knob is available at reichelt.de, the case at conrad.de.

I also made a PIMETA in a silver aluminum case:
silver PIMETA
ATM, it sports an AD8620 and dual BUF634s on the L and R channels, and an AD8610 and a single BUF634 on the ground channel. Alps blue velvet pot, Elna Cerafine 470 µF caps, Wima 10 µF bypass caps. Bulgin dual 9 V battery slider. The power switch is made by Marquardt (1802 series, available from Conrad). The case (made by Isel) is available at reichelt.de, but I used black M3x20 screws from Conrad. The knob is a "dome speed" type for electric guitars.

 

[MisterX]

Nice pimeta till.

Are the grounds on the jacks in the Pimeta isolated from the case?
If not they essentially short out the ground channel.....