I know that...... The modi 2 is my DAC...... I am going to pick up a 2 channel amp, probably used from CL, and use the combo to replace aging Sony ES receiver.
Sorry have a headache. Had to reread your post LOL. You are wanting to use the Vali 2 as a preamp. Sorry cant help you there as I only use it as a hp amp.
The Vali 2 is my first tube amp, and I`m having a blast with it. I also got an EH 6922 as my first tube rolling, and it sounds really, really good, much better than the stock one (that does not seem to have any identification on it).
I have been reading this thread and the tube rolling one, and by its description it seems an octal tube would be a nice adition, considering a more tubey, warm sound.
I already got a socket saver and an adapter, so I was wondering if anyone could give some suggestions on octals.
The Vali 2 is my first tube amp, and I`m having a blast with it. I also got an EH 6922 as my first tube rolling, and it sounds really, really good, much better than the stock one (that does not seem to have any identification on it).
I have been reading this thread and the tube rolling one, and by its description it seems an octal tube would be a nice adition, considering a more tubey, warm sound.
I already got a socket saver and an adapter, so I was wondering if anyone could give some suggestions on octals.
The new Massdrop x Cavali Hybrid Tube amp seems to disrupt Schiit's line of affordable products. I'd love to read more comparisons between the MCHT and the Vali 2 in the time to come.
The new Massdrop x Cavali Hybrid Tube amp seems to disrupt Schiit's line of affordable products. I'd love to read more comparisons between the MCHT and the Vali 2 in the time to come.
The only issue I met with Vali2 is, when I use T50RPmod on high gain, volume at 3 o'clock, the whole sound is distorted. (With SS amps, they are fine).
Is this because...
- Output power of Vali2 is not enough to drive T50RP at a loud volume?
- Output impedance of Vali2 (5.8 ohms on high gain) is too high for T50RP (50 ohms)? It seems to be ok according to the 1/8 rule though.
- Nature of tube? (especially with planars?)
Gotcha, unfortunately I can't get enough volume with low gain, so probably need to upgrade my amplifier to Lyr2 or upcoming Massdrop Cavalli one, which has lower output impedance on higher gain...
How are you not getting enough volume? It puts out a crazy amount of power. I think it is distorting because you are driving them far louder then the drivers can handle. Its putting out 650mw per channel @ 50ohms.
How are you not getting enough volume? It puts out a crazy amount of power. I think it is distorting because you are driving them far louder then the drivers can handle. Its putting out 650mw per channel @ 50ohms.
I'm going to order an 1/8 inch to RCA cable to preamp my Vali 1 into my Panache and see how it differs from pure solid state. I had difficulty hearing any difference with MJ2, but perhaps Vali 1 is more colored.
The Vali 2 is my first tube amp, and I`m having a blast with it. I also got an EH 6922 as my first tube rolling, and it sounds really, really good, much better than the stock one (that does not seem to have any identification on it).
I have been reading this thread and the tube rolling one, and by its description it seems an octal tube would be a nice adition, considering a more tubey, warm sound.
I already got a socket saver and an adapter, so I was wondering if anyone could give some suggestions on octals.
I'm using a Raytheon black plate. To me, it gave mid and sub-bass more depth without interfering with the mids too much. Soundstage isn't the widest, but it's not claustrophobically close. It's my current daily driver and their cheap, so that's a plus.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.