[steve2151]

Mine has the serial number (NK10----) in blue on the inside of the left earpiece and in red on the right. It's a bit hard to read against the gold flakes and amber, but it's almost impossible to confuse left/right on a CIEM anyway.
 
I think different colored ear canals are also an option if you really want it to be obvious.

 

[kh600rr]

The writing on them should be in red and blue, also, they will only fit one ear. :wink_face:

Thanks Gumpy!! You mean, I shouldn't use a Ball Peen hammer, if I can't get the left side , to fit in the right?

 

[Watagump]

Thanks Gumpy!! You mean, I shouldn't use a Ball Peen hammer, if I can't get the left side , to fit in the right?

You can try it, might help get a better seal.

 

[kh600rr]

I went with The Wizard design, some Gold flake, I like, others not so much. I didn't put anything in the request section. Just rolling the dice.

 

[chiman]

Hey Noble Peeps, on the K10, how, and where are left & right sides marked? Is it fairly easy to tell? On my IE-800's, it's really tiny. Pain in the butt.

I'm still using the stock cable, so I usually look at the curve of them from the iem end to tell me which side is which.

 

[Hawaiiancerveza]

How close does the R sound to the 4C sound?
Quote:

   
Hello Alpha421
 
The switch concept is sold in CIEM format as follows:
 
 
The Switch is an "option" for the CIEMs. The option is called "R" (for reference)  and the CIEM models 3c, 4c, & 5c can carry the option.
 
What would happen is, if someone was to purchase the 3c-r
 
they would purchase a 3C and select the "R" option (an additional $275)
 
The switch is added to the CIEM, along with a reference driver, thus a 3C really houses 4 drivers per side.
 
 
But as far as the PR and FR, those are only offered in IEM format.
 
 
Tzar 90....   no comment

 

[FullCircle]

 

 
The r is essentially ruler flat, up until around 1.5 - 2Hz with a increase to make up for resonant loss.

 

[kova4a]

   
The r is essentially ruler flat, up until around 1.5 - 2Hz with a increase to make up for resonant loss.

It shouldn't be hard to make it flat up to 2Hz  

  You should probably try doing it to 2kHz lol

 

[FullCircle]

  It shouldn't be hard to make it flat up to 2Hz  

  You should probably try doing it to 2kHz lol

 
Sorry, but Im not catching the humor as of late.

 

[FullCircle]

 
 
Felt I best make another set of N6 "dress" IEMs

 

[kova4a]

   
Sorry, but Im not catching the humor as of late.

Nah, it's my bad - it's not really funny. I'm sure you meant 1.5 - 2kHz

 

[FullCircle]

  Nah, it's my bad - it's not really funny. I'm sure you meant 1.5 - 2kHz

 
correct

 

[Watagump]

 
 
 
Felt I best make another set of N6 "dress" IEMs

 
 
Hotness, I was almost going to PM you to make a blue pair.

 

[OK-Guy]

those are mine... Claret & Blue.... yummy, yummy, & more yummy.

 

[OK-Guy]

for ibreezy:

Switch on your ZX1 WiFi, go to Settings -> About Device -> Software Update. The ZX1 will download the 280MB or so file and ZX1 will update upon rebooting.
 
tell me the results with the K10's after...

 
(spoiler)... it's immense with the N5's.