When you start using sinegen, do you press the power button as a song is playing?
Also what settings do you put the level (-db) at? By default it opens at -15 and when played with a song, the volume of the song is unchanged. However, the picture in the tutorial shows the levels set at 0, and when played with a song, the song's volume decreases slightly.
When you start using sinegen, do you press the power button as a song is playing?
Also what settings do you put the level (-db) at? By default it opens at -15 and when played with a song, the volume of the song is unchanged. However, the picture in the tutorial shows the levels set at 0, and when played with a song, the song's volume decreases slightly.
Sinegen is used to seek the frequency response humps and valleys of your headphones, so you don't need to play any songs. Just press the power button, listen to the tone, and move the slider up and down until you can hear the tone becomes louder of softer on certain frequencies.
Most of the time you'll find the tone gets very loud between 7 - 8 kHz.
It is better if you do that to each channel separately by setting the level -100 on one of the channel. It's because left and right cups usually have different frequency response.
Sinegen is used to seek the frequency response humps and valleys of your headphones, so you don't need to play any songs. Just press the power button, listen to the tone, and move the slider up and down until you can hear the tone becomes louder of softer on certain frequencies.
Most of the time you'll find the tone gets very loud between 7 - 8 kHz.
It is better if you do that to each channel separately by setting the level -100 on one of the channel. It's because left and right cups usually have different frequency response.
When using Electri-Q as a VST on Foobar, do you load it together within foobar as you play the pink noise? Or separate (as an application) from Foobar, and then load it (depending on what EQ you achieved) to play audio through the DSP/VST.
When using Electri-Q as a VST on Foobar, do you load it together within foobar as you play the pink noise? Or separate (as an application) from Foobar, and then load it (depending on what EQ you achieved) to play audio through the DSP/VST.
When I had my Macbook Pro setup as a music server, I used IZotope Ozone 5 which you can get here. While it is aimed at mastering a recording session, it can be easily be used as an EQ. It has other useful 'compression' features and great graphics displays that I liked. You would need the basic program not the advanced.
edit: I used the Ozone 5 with Audirvana Plus music player that integrates with iTunes. Check it out here.
I've been finding peaks on my headphones and equalizing them successfully now, but a new problem has risen. When I play back a song and try listening to it with and without the EQ, I can 'feel' a loss of fidelity in the EQ profile with the chopped peaks, even when I've reduced the gain of the peaks only around 4dB. The width of my bands is no larger than 0.2 8va. Is it supposed to feel this way? Especially when chopping that peak around 6800 kHz, the music sounds slightly muffled afterwards. What do you guys think?
I don't know what method you use to achieve the EQ, but muffled sound is the opposite of a well equalized signal. When I switch from EQ to bypass (no EQ), it sounds like I've got cotton in my ears. With the EQ the detail and sound stage are amazing.
I don't know what method you use to achieve the EQ, but muffled sound is the opposite of a well equalized signal. When I switch from EQ to bypass (no EQ), it sounds like I've got cotton in my ears. With the EQ the detail and sound stage are amazing.
Just the standard method of finding the peaks with a sine wave, then using a pink noise to flatten out the peaks. I takes about -7db for the peak at 6800 Hz (band width 200 Hz) to flatten out for me, but that results in a slightly muffled sound, which I perceive as loss of fidelity.
By adjusting for the resonant frequency for the ear canal, aren't we modifying the signal in possibly negative way? Assuming that the sound engineer uses active monitors for proofing and recording, then that very well includes the resonant frequency of his ear canal. By, flattening these peaks, aren't we listening something not the way intended by him?
^ Not really. Lots of things change the frequency response before the sound gets to our brain. The source / DAC, cable interconnects, Amplifier, choice of vacuum tubes, headphone cable, headphones, outer ear, our inner ear, and our neurological response all have an effect on the frequencies we 'hear'. Even headphones that are equalized using a frequency analyzer still need to be adjusted, to some extent, to the listener's experience. It is a tricky process and needs to be practiced. When it is done correctly there is an obvious improvement in the SQ.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.