1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.

    Dismiss Notice

Chord Electronics ☆ Poly ☆ (wireless & microSD module for Mojo) ☆★►USEFUL INFO on 1st PAGE!!◄★☆

Discussion in 'Portable Source Gear' started by Matt Bartlett, Jan 5, 2017.
First
 
Back
957 958 959 960 961 962 963 964 965 966
968 969 970 971 972
Next
 
Last
  1. Yourmomm
    Anyone else have the weird problem of frequent drop-outs of roon internet radio, (even low res radio stations), yet fairly reliable connection for roon tidal? (And all other roon functionality).

    Annoying, as requires switching from "roon" to "everything else" mode (and back again), every time I want to listen to the radio....
     
  2. Edric Li
    Question: does mojo-poly playing from an sd card has eq functionality on the mobile phone app? thanks in advanced.
     
  3. Mightygrey
    No.
     
  4. DavidW
    A new twist after consistent performance with my Poly. I replaced my Mojo battery yesterday following these steps. After completing the swap, I reconnected the Mojo to the Poly to test that all functions worked properly. I then charged the Mojo separately for ten hours and then reconnected the Mojo to the Poly last night for an overnight charge of both units.

    This morning, Gofigure failed to connect. When I first booted up the MojoPoly, the P light flashed blue and green before going dark. I am now charging the Poly separately in case the Mojo consumed power from the Poly. Seems unlikely as the Mojo had the full ten hour charge.

    Any thoughts what may be going on and what to do?
     
  5. DavidW
    A few hours later...

    After charging the Poly alone for just two hours and reconnecting it to the Mojo, all is working well and (surprisingly) with a full battery. Very strange.

    IMG_0262.PNG
     
  6. Stourmead
    Hi Matt
    any update on the native Qobuz support or is that option kyboshed for the time being?
     
  7. Matt Bartlett
    No I'm afraid I haven't had an answer back from Qobuz yet. I'll chase this up.
     
    Chord Electronics Stay updated on Chord Electronics at their sponsor page on Head-Fi.
     
    https://www.facebook.com/chordelectronics https://twitter.com/chordaudio http://www.chordelectronics.co.uk/
    Stourmead and Peter Hyatt like this.
  8. Disothers
    Hi everyone,

    I just received my new poly to play with mojo today, but I had an issue with connecting Gofigure. To be short, Gofigure couldn't recognize my Poly at all in the Wizard process with both the poly and my iPhone's Bluetooth & GPS on. Later the config page showed no firmware #, it only showed '2016' at the bottom of the page. So I assumed my Poly has the oldest firmware.
    Now my questions are: How can I update the mojo without Gofigure? Right now, each time I turn on the Poly, the P-status repeats: red, blue, green for about only 30 seconds, then it turns to the stable color to indicate the battery %.
    I tried to use the pin to switch to the firmware mode many times based on the online manual, but I could only switch between the network mode and the access mode.


    Thank you very much!

    Kevin
     
  9. Stourmead
    I had no luck until I popped a blank sd card in. Then it was torture but eventually it updated past version 2
     
    Last edited: Nov 8, 2019
  10. miketlse
    Have you managed any progress with updating your Poly?
    The early firmware versions (until v 1.0.41) used automatic updating, which needed the owner to leave the Poly connected to the internet, and the Poly would automatically connect to the Chord server then download the update (if needed). The owner then needed to switch off the Poly, and then reboot it, in order to install the new firmware. The progress through this process was indicated by which sequence of lights was flashing and which colour. It was always difficult for owners to watch the Poly status lights for hours on end, in order to monitor the progress, and so there were posts about poly downloading the update without the owner being aware - one knock-on effect that the poly had not yet been rebooted to enable the update to be completed.

    After version 1.0.43 the update is requested by the owner using gofigure, and this makes the process more predictable/intuitive for many owners.

    The firmware versions are explained in more detail in this FAQ, under the heading 'HOW DO I UPDATE POLY, WHAT IS THE LATEST POLY FIRMWARE VERSION AND WHAT IMPROVEMENTS HAVE BEEN MADE?'

    If you are still experiencing issues, then there are plenty of owners on this thread who will be glad to advise.
    The alternative is to contact Chord support via their website, or email them on support@chordelectronics.co.uk and someone will be able to talk you through the update process.
     
    GreenBow likes this.
  11. Disothers
    Thanks. Mine finally got it work by just fully charged it and waited
    Hi, after hours and hours, finally got to the boat (2.04 it is). The new firmware work great. Thanks for all the support.
     
    miketlse, sergeywin1 and Stourmead like this.
  12. jldevo
    I’ve recently updated poly to latest fw. Now MPDluxe does not recognise any songs on my sd card. 8player works as normal. Any ideas why this has happened and how I correct it. Thanks in advance. J.
     
  13. PrittiPoly
    I have MPDluxe 1.8 working on iOS 12.4.3. Poly 2.04.
     
  14. jldevo
    iOS 12.1.4 MPDluxe 1.8. Poly 2.0.4. here. Maybe updating iOS might fix it.
     
  15. PrittiPoly
    Worth trying. If no joy, there are other MPD clients: Rigelian, MaximumMPD, MPDPlayer.
     
First
 
Back
957 958 959 960 961 962 963 964 965 966
968 969 970 971 972
Next
 
Last

Share This Page