Share if what was balanced or 3.5mm? Volume level? And will do the same test.8h was measured by a stopwatch from 100% to shutdown. On the latest firmware. I used Qobuz versions higher than 7.13, now 7.14.1. Wifi choose 2.4Mhz. AB+Nos
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
Astell&Kern Launches New R-2R DAP and IEMs at High End Munich 2023
- Thread starter JasonNYC
- Start date
4.4 balanced vol 73-90 On older tracks, you have to turn up the volume.Share if what was balanced or 3.5mm? Volume level? And will do the same test.
After the update from Astell, the player began to work longer. And also after the Qobuz updates.
I reset the Qobuz cache before testing. There are no saved tracks. Everything was played back via 2.4wifi.
Do not look at the charge, which is not shown correctly in %. It will be consumed very quickly at first, but then it will stabilize and go away more slowly. It took me 8.5 hours. Even if you safely remove 1 hour for a slightly more frequent activation of the player screen, you get 7.5 hours. It's still a good result.
When transitioning between NOS or OS modes, or shifting between Class A/AB modes without playing music, a noticeable sound is present. Moreover, occasional sounds occur when opening music files, and there is an intermittent popping sound. Strikingly, if mode switches take place during music playback, the aforementioned issues do not manifest. Is this indicative of a hardware malfunction or a software-related problem?
Tested right now, only changing from AB to A I've heard the popping sound and just once, after that switched many times and no sound, afterwards when playing the first track after changes heard a small popping sound before the music started, hope it helps!When transitioning between NOS or OS modes, or shifting between Class A/AB modes without playing music, a noticeable sound is present. Moreover, occasional sounds occur when opening music files, and there is an intermittent popping sound. Strikingly, if mode switches take place during music playback, the aforementioned issues do not manifest. Is this indicative of a hardware malfunction or a software-related problem?
Probably nothing is wrong with your unit.
Only one question. Ti or original se300 version? Is Ti worth overpaying? Any suggestions?
Last edited:
It's not even discussed that the titanium version is much better in sound... take it, especially since the difference in cost is not so big. In addition, it has recently been revealed that the titanium version works little faster. Yes In the aluminum version, all settings are completely reset, as well as. We compared both devices in real time.Only one question. Ti or original se300 version? Is Ti worth overpaying? Any suggestions?
wipe data. this is easy to do. maybe it will be useful to someone.
Instructions: turn off the player. pinch and hold the button of the previous track and without releasing it, press the power button. the "no command" window will appear. release the buttons and quickly and briefly press the power button of the player and turn the volume wheel up at the same time. select the wipe data / factory reset option. turn the volume wheel and confirm by pressing the turn on button of the player briefly. After that, select reboot system now. The entire player will be completely reset.
Last edited:
Hi! I have Thieaudio Monarch mk3. Maybe, someone tried them with se300/se300ti. What are the impressions? Especially interested in bass and clarity?
Very good with the se300. The MK3 allows you to hear very well what the device is capable of.Hi! I have Thieaudio Monarch mk3. Maybe, someone tried them with se300/se300ti. What are the impressions? Especially interested in bass and clarity?
pippen99
Headphoneus Supremus
So I got the case for the SE300 today. I can feel the side buttons working fine but the power button will not activate through the case. I am using a fingernail and pushing hard. I would not expect they would leave it up to me to cut that out. It seems to be too thick and the power button is a little recessed. Anyone else have this issue?
pippen99
Headphoneus Supremus
So it seems the button is nearer the front of the case than the indicator engraved on the case. Just took a little while to figure out.
The only way to solve this issue is to act this way)))So I got the case for the SE300 today. I can feel the side buttons working fine but the power button will not activate through the case. I am using a fingernail and pushing hard. I would not expect they would leave it up to me to cut that out. It seems to be too thick and the power button is a little recessed. Anyone else have this issue?
Attachments
Marcellos
New Head-Fier
Hi, I'm a new member I apologize if this topic has already been discussed and I missed it but what can you tell me about the comparison between SE300 and SP2000T? Which one would be better to buy now?
Greetings, Marcello (Italy)
Greetings, Marcello (Italy)
Er…. I put a piece of tape over the button to decrease the gap between the button and the case. It worked.The only way to solve this issue is to act this way)))
Richdgrant
Head-Fier
Quick question, is there a difference in the quality of the implementation of the single ended and balanced outputs on the SE300? I’ve read that some DAPs and DACs have a better implementation of one over the other sometimes.
And following on from that, can the balanced output of a DAP change the frequency response of an IEM enough for it to be audible compared to the SE output?
And following on from that, can the balanced output of a DAP change the frequency response of an IEM enough for it to be audible compared to the SE output?
Last edited:
R7photo
100+ Head-Fier
- Joined
- Apr 28, 2017
- Posts
- 325
- Likes
- 292
You may get several answers but im sure bal better as squeeze out more powerQuick question, is there a difference in the quality of the implementation of the single ended and balanced outputs on the SE300? I’ve read that some DAPs and DACs have a better implementation of one over the other sometimes.
And following on from that, can the balanced output of a DAP change the frequency response of an IEM enough for it to be audible compared to the SE output?
/////
Please note I received recently a new Iem and started using it with a 20 dollar 4.4 cable that was new
Switch to included 3.5 cable and big sq difference for better out of 3.5, with included cable
Cheap 4.4 cable being returned
Gonna try a better 4.4 cable when received
I would say give it a try on terminals see which one best
Last edited:
Users who are viewing this thread
Total: 3 (members: 0, guests: 3)