Sounds like a cable/contact problem. Wiggle the cables. Clean the plugs. Make sure nothing moves while playing and see if it still happens.
Just came to same conclusion. One of the laptop USB ports is dying.
Last edited:
Sounds like a cable/contact problem. Wiggle the cables. Clean the plugs. Make sure nothing moves while playing and see if it still happens.
Just came to same conclusion. One of the laptop USB ports is dying.
Stay updated on iFi audio at their sponsor profile on Head-Fi.
|
just for your information. i have nano igalvanic3.0 connecting to micro iusb3.0. igalvanic connecting to computer and iusb connecting to dac.
i have ortofon usb2.0 cable, oyaide continental 5s v2 usb2.0 cable, uptone USPCB A>B Adapter and amazon basic usb3.0 and stock blue3.0.
from in and out of igalvanic, only usb3.0 cables work. from iusb to dac, only ortofon work. oyaide and USPCB A>B Adapter never worked at anywhere.
in conclusion, there is no high end usb3.0 cable available at the moment and unknown amount of audiophile usb2.0 work. that means if you want to use nano igavanic3.0 and micro iusb3.0 together to achieve the highest performance as suggested by ifi, you have no choice and have to use cheap usb3.0 cable or to spend a lot of money to try and error the hifi grade usb2.0 cables. new mercury3.0 and gemini3.0 are out but i am not sure if i should consider them high end.
Alright, you've asked for it, here it goes then...
iFi USB options with full galvanic Isolation
- Ultimate Performance - iUSB 3.0 micro with iGalvanic 3.0 nano
- Very High Performance - iUSB 3.0 nano with iGalvanic 3.0 nano
- High Value - iGalvanic 3.0 nano with iDefender and iPower
- Historical Value Upgrade - original iUSB Power (discontinued) with iGalvanic 3.0 nano
- Lowest Cost - iGalvanic 3.0 nano
iFi USB Options without Galvanic Isolation (but with iSOGround ground loop breaker)
- Ultimate Performance - iUSB 3.0 micro
- Very High Performance - iUSB 3.0 nano with iDefender (no extra iPower needed)
- High Value - iPurifier 2.0 with iDefender and iPower
- Historical Value Upgrade - original iUSB Power (discontinued) with iPurifier 2.0
iFi USB Problem Solvers
- USB 2.0 signal regenerator (e.g. long cables, improved signal integrity) - iPurifier 2.0 A or B
- Earth/Ground-loop with DAC that operates on USB power - iDefender with iPower
- Earth/Ground-loop with DAC that does not draw power from USB power (e.g. Handshake only use of VBUS) - iDefender only
- RFI & USB Power noise reducer - iSilencer
iFi non-USB problem solvers
- iPower - super clean 5V/9V/12V/15V DC power supply
- iPurifier DC - clean up any DC power source 5V - 24V up to 3.5A load (e.g. Laptop, pro audio gear)
- iPurifier SPDIF - Jitter killing memory buffer with highly precise clock, to clean up poor quality SPDIF feeds
We sincerely hope this will help, though it depends on a system and problems it might have.
https://ifi-audio.com/portfolio-view/micro-iusbpower/It seems like the function of iUSB Power (discontinued) is same to idefender with ipower?
If so, how are they compared in performance (the original iUSB Power with the adapter in package and idefender with ipower)?
i have uninstalled the driver, connected all the decives, then reinstalled the driver. even worst. disconnect within minutes!I had similar problems running my DIY 2.0 cable into the Galvanic 3.0 until I reinstalled the Oppo Sonica USB driver. The supplied blue cable worked fine but I suspected it was degrading absolute sound quality compared to my neotech silver gold OCC 2.0. I first synched my Oppo Sonica. Then I hooked up the W4S reclocker and reloaded the driver. I use uptone pcusb A/B blocks in and out of the W4S. Then I hooked the Galvanic 3.0. Made it all one connected chain. Then synched the entire combination and reloaded the driver again for good measure. It was working after the previous reload. But I wanted my computer to see it as one combined component when it loads the driver on boot up. Works great now. Jplay is more stable than ever and I can even run DSD files at highest Dac Link and lowest buffer settings now; which sounds best with the Sonica DAC.
I'm running Mercury USB 3.0 cables between AudioPC, Nano USB 3.0, iG3, and DAC. They've replaced the trusty good sounding Curious USB links. They've been here since last night, so I expect them to be more open. That said, I feel that they're a MUST for those of us who have invested in iUSB and iG3, to say the least.i have uninstalled the driver, connected all the decives, then reinstalled the driver. even worst. disconnect within minutes!
i dont understand, if iusb and igalvanic is transparent to the computer, why it shows differently in usb device viewer?
iusb+igalvanic