Master Clock Talk

Dec 10, 2022 at 6:00 PM Post #152 of 3,887
In the case of square wave output, the connectors are not good for both. They just say so to avoid further questions and panicking “audiophiles”.
I knew there was some kind of esoteric logic to this. Please enlighten me(not joking)
 
Dec 10, 2022 at 6:09 PM Post #153 of 3,887
I knew there was some kind of esoteric logic to this. Please enlighten me(not joking)

Yes I'm glad you asked. I'm certainly not panicked, and feel quite confident regarding LHY.
 
Last edited:
Dec 11, 2022 at 2:19 AM Post #155 of 3,887
Can i connect the master clock directly to my DAC because my DDC does not have clock input?.
These clocks work with any DAC that has a BNC input for a 10 MHz clock.

Not all DDCs have an input and most DACs do not either.
 
Dec 11, 2022 at 1:23 PM Post #158 of 3,887
What impedance did you choose for ddc/dac?

50ohm gear over here.

Actually my DAC is almost 10 years old and I breathed new life into it with a great DDC and i2s connection. No clock input to the DAC.
 
Dec 11, 2022 at 3:14 PM Post #159 of 3,887
I just received my "After Dark" clock. It was supposed to have some outputs at 50ohm and some at 75ohm. But all the BNC outputs look the same.

I thought the 50 ohm outputs have thicker plastic around the pin to differentiate it.....

Could someone please advise me if this is correct....
 
Dec 11, 2022 at 3:29 PM Post #160 of 3,887
I just received my "After Dark" clock. It was supposed to have some outputs at 50ohm and some at 75ohm. But all the BNC outputs look the same.

I thought the 50 ohm outputs have thicker plastic around the pin to differentiate it.....

Could someone please advise me if this is correct....
Pictures
 
Dec 11, 2022 at 3:32 PM Post #161 of 3,887
I just received my "After Dark" clock. It was supposed to have some outputs at 50ohm and some at 75ohm. But all the BNC outputs look the same.

I thought the 50 ohm outputs have thicker plastic around the pin to differentiate it.....

Could someone please advise me if this is correct....

I understood from posts upthread it comes with only 50 ohm connectors regardless of impedance.
 
Dec 11, 2022 at 3:52 PM Post #162 of 3,887
My order was supposed to have two 50ohm outputs and two 75ohm outputs.

All the BNC outputs on the back of the unit look the same and all of the cables that came with it are 75ohm. I assume they messed up- but I don't want to jump the gun.
 
Dec 11, 2022 at 3:59 PM Post #164 of 3,887
My order was supposed to have two 50ohm outputs and two 75ohm outputs.

All the BNC outputs on the back of the unit look the same and all of the cables that came with it are 75ohm. I assume they messed up- but I don't want to jump the gun.
From what I read here, the connectors don't get changed. If you order with a mix of outputs, the circuit impedance should be set to what you ordered. But you can't tell by looking from the outside. Maybe open the box and check if the DIP switches are set (not sure, but since it's user-configurable I guess there are DIP switches)
 
Dec 11, 2022 at 4:00 PM Post #165 of 3,887
Could I connect OCK-2 to Gustard U18 and Gustard X26 Pro at the same time?
Would both have improvements?
If both devices have 10 MHz inputs then yes. This is the way a Master Clock is supposed to be used- you drive all your downstream devices from the same clock. That way everything is in beautiful harmonious synchronization :)
 

Users who are viewing this thread

Back
Top