[Cevisi]

Someone have a set of bellsing 10013 for sale OR know how to get Them?

Soundlink still sell them in china i think they send you some when you ask (and dont live in the us i think)

 

[TOBIJampar]

Someone have a set of bellsing 10013 for sale OR know how to get Them?

If you don't live in the US, contact SoundLink. They might be able to send them to you even if they are no longer listed in the Shop.
Worked for me

 

[Madmike1988]

Soundlink still sell them in china i think they send you some when you ask (and dont live in the us i think)

Thanks, in from Holland and contacted soundlink but they are out of stock they said!

 

[Farquarl]

Hey,
Does any one know a good Tipp to get a few dB more at 3khz? Without changing drivers.

 

[Xymordos]

Hey,
Does any one know a good Tipp to get a few dB more at 3khz? Without changing drivers.

What's the driver combination? Looks pretty good.

 

[dhruvmeena96]

Hey,
Does any one know a good Tipp to get a few dB more at 3khz? Without changing drivers.

This iem ain't tip sensitive.


There is no peak to shift..

 

[Farquarl]

What's the driver combination? Looks pretty good.

HODVTEC, Bellsing Twfk, ED

They allread sound amazing tbh, but I think just a tad more at 3khz would be great.

This iem ain't tip sensitive.


There is no peak to shift..

What do you mean by "tip sensitive"?

 

[Xymordos]

HODVTEC, Bellsing Twfk, ED

They allread sound amazing tbh, but I think just a tad more at 3khz would be great.


What do you mean by "tip sensitive"?

Can you change the damper or XO?

 

[wardy]

Can anyone suggest some good books on accoustics? Especially ones that could be applied to iems

Cheers

 

[GourmetEnte]

Hey guys, I've been building the finale 2 IEM in a universal fit shell. When test hearing it sounds rather shouty. I was wondering if I'd have to adjust tube length due to the fact that I'm using a universal fit, cheers

 

[dhruvmeena96]

Hey guys, I've been building the finale 2 IEM in a universal fit shell. When test hearing it sounds rather shouty. I was wondering if I'd have to adjust tube length due to the fact that I'm using a universal fit, cheers

Your ED30761 looks like full covered. The vent looks closed off

This will cause the bass to die and make mids more prominent

Plus... There was no components in the iem... If I remember correctly.

 

[GourmetEnte]

Your ED30761 looks like full covered. The vent looks closed off

The driver isn't fully closed off. However I don't know where the vent is when looking at the driver and schematics provided by Knowles. Is it on the back? If so then it shouldn't be an issue as it isn't covered.

Plus... There was no components in the iem... If I remember correctly.

If you're referring to the two resistors: those are two 1ohm resistors. The design calls for 1 2ohm resistor.

Cheers

 

[tomekk]

I've been building the finale 2 IEM in a universal fit shell. When test hearing it sounds rather shouty

Pads, if it's a mistake (I see two open pads), can cause asymmetrical peaks. You should also close the shell to compensate the chamber pressure.

Edit:

 

[dhruvmeena96]

Pads, if it's a mistake (I see two open pads), can cause asymmetrical peaks. You should also close the shell to compensate the chamber pressure.

Edit:

Yah.... This one I was talking about.

 

[dhruvmeena96]

The driver isn't fully closed off. However I don't know where the vent is when looking at the driver and schematics provided by Knowles. Is it on the back? If so then it shouldn't be an issue as it isn't covered.


If you're referring to the two resistors: those are two 1ohm resistors. The design calls for 1 2ohm resistor.

Cheers

Ohhh the minor compensator I called for.


The issue of shoutiness is due to covering of vent