[Shilohsjustice]

Interesting. From what I read about the Polylux, it says it removes all the oxygen so no baths are required. Or do you have a different model that does not remove the oxygen?

This is an older model and does not remove the oxygen. In fact it's so old I can't find any information on it.

 

[Shilohsjustice]

This is an older model and does not remove the oxygen. In fact it's so old I can't find any information on it.

It was pulled from service from a hearing aid lab. It cost $150 shipped. The only thing I had to do was get an up converter to go from 110v to 220v $39.99 from Amazon. Works better than I expected.

 

[Squirg]

Just got this stuff in...
 
http://www.ebay.com/itm/170708941257?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
 
Apparently, this is what many are using to coat impressions.  Not been very happy with Paraffin wax.  Going to heat it up tonight and coat a few sets of impressions.  I let you know how it goes!
 
Wish me luck...

 

[Shilohsjustice]

The polylux 1000 and newer models remove oxygen during cure. Like in the picture below.




This person has had this on eBay for a long long time, someone could probably offer them less than asking and they would take it as its been up for so long.

 

[MuZo2]

  Just got this stuff in...
 
http://www.ebay.com/itm/170708941257?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
 
Apparently, this is what many are using to coat impressions.  Not been very happy with Paraffin wax.  Going to heat it up tonight and coat a few sets of impressions.  I let you know how it goes!
 
Wish me luck...

I have same.

 

[Shilohsjustice]

Hello all, it's been awhile since I posted anything I've been working on.

Here is a single driver setup I did for a friend, I used a BK-28562 from a set of shure e3's they had that were broken. A 680ohm damper, and my new universal shell design that I made myself (not a clone).

 

[Squirg]

The polylux 1000 and newer models remove oxygen during cure. Like in the picture below.

Dude!  I need this!!!  Does it require a gas hookup of some kind?


This person has had this on eBay for a long long time, someone could probably offer them less than asking and they would take it as its been up for so long.

 

[Shilohsjustice]

No, it's a sealed unit. Doesn't need a gas hook up at all.

 

[Shilohsjustice]

Squirg, did you get it??? The listing just came down, it's literally been up for over a month.

 

[Squirg]

Squirg, did you get it??? The listing just came down, it's literally been up for over a month

Dammit!  Nope, but I already had my script planned out for my wife when I got home!  

 

[Shilohsjustice]

Dammit!  Nope, but I already had my script planned out for my wife when I got home!  

I rotate through scripts weekly! Like I bought drivers to do a Savant clone, I said it was for a friend. Secretly its for me as I liked the Savants but didn't have $600 to shell out. Instead $42 dollars for some drivers, hahahaha I love DIY!!!!!!!

 

[Shilohsjustice]

I'll bet someone here on the forum who seen my post bought it though!!!

 

[mikkelmmk93]

Hi everyone
Where can I get the coloured litz wire? Like the metallic green, red, blue and such - preferably in EU.

 

[Squirg]

  Hi everyone
Where can I get the coloured litz wire? Like the metallic green, red, blue and such - preferably in EU.
 

I've had good luck with this stuff.  The coating is a little thicker but not much.  Just make sure you burn it off when tinning the ends...
 
http://www.ebay.com/itm/T028G-10m-GREEN-0-28mm-Teflon-Micro-Litz-Wire-Solder-High-temperature-10m-1pcs/191957441710?_trksid=p2047675.c100011.m1850&_trkparms=aid%3D222007%26algo%3DSIC.MBE%26ao%3D1%26asc%3D39218%26meid%3D2f7080f206b64f1bb1a30a4b07b42f4e%26pid%3D100011%26rk%3D4%26rkt%3D11%26sd%3D191934616023

 

[mikkelmmk93]

  I've had good luck with this stuff.  The coating is a little thicker but not much.  Just make sure you burn it off when tinning the ends...
 
http://www.ebay.com/itm/T028G-10m-GREEN-0-28mm-Teflon-Micro-Litz-Wire-Solder-High-temperature-10m-1pcs/191957441710?_trksid=p2047675.c100011.m1850&_trkparms=aid%3D222007%26algo%3DSIC.MBE%26ao%3D1%26asc%3D39218%26meid%3D2f7080f206b64f1bb1a30a4b07b42f4e%26pid%3D100011%26rk%3D4%26rkt%3D11%26sd%3D191934616023

Thanks - but does it look "metallic" like in this photo? http://i58.tinypic.com/255o12c.jpg 
I know it is really silly to get one specific type of cable - but I've always thought that it looked amazing.