Sound in general. Nothing to do with the second harmonic feature. I have not been able to hear any differences but Fiio mentioned it is only noticeable at higher volumes.
I see no reason why that would be any different on the Q7 versus any other device. I am not sure how you A/B test for subtle changes when you have to update the firmware in between times, unless of course you have access to two Q7 with different firmware and an A/B switch set up.
You're correct. This is why I said I could be biased because I spent more time testing the demo unit that was on the old firmware. There is no anecdote evidence firmware would change the sound signature and there is no reason to. So I am dismissing what I heard as placebo.
The output impedance of the single ended output will be lower so that might have an effect on the sound if using very low impedance IEM, more than the difference in power would I would venture.
This is true. I noticed the single ended output being lower so I thought that could be the case. I preferred the SE output with the IE 600 because bass tones sounded 'rounder'. With the BAL output, the bass sounded too clean if that makes sense. However I will say the BAL side makes improves separation considerably. It is just that good. I also have the IER-M7 and I prefer that set on the BAL side.
Could the FiiO Q7 power supply be overkill at 12V/2A/24W ? I checked with a power measuring device and it outputs only 12V/0.35A/4.2W in Ultra High Gain with my Denon D9200 at high volume and 4.4mm balanced cable. I wonder how high the power draw can go with harder to drive headphones.
Edit : i also tried with a 150ohm 3.5mm adapter and power draw was about 0.27A/3.2W in Ultra High Gain at maximum volume (120)
Could the FiiO Q7 power supply be overkill at 12V/2A/24W ? I checked with a power measuring device and it outputs only 12V/0.35A/4.2W in Ultra High Gain with my Denon D9200 at high volume and 4.4mm balanced cable. I wonder how high the power draw can go with harder to drive headphones.
Edit : i also tried with a 150ohm 3.5mm adapter and power draw was about 0.27A/3.2W in Ultra High Gain at maximum volume (120)
Could the FiiO Q7 power supply be overkill at 12V/2A/24W ? I checked with a power measuring device and it outputs only 12V/0.35A/4.2W in Ultra High Gain with my Denon D9200 at high volume and 4.4mm balanced cable. I wonder how high the power draw can go with harder to drive headphones.
There are other things that you have not accounted for.
1. During DC fast charging where Q7 will draw current at 12V. Not sure if it is charging at 2A but the Q7 does top charge relatively quickly even during usage.
2. Q7's own power consumption
The power supply will send as much current at 12V as needed up to its maximum rated 12V/2A (24W). I believe you're right in that there may be some extra headroom which is always nice.
Yep, you'll need an oscilloscope (even the most basic one) to see the output properly. With a sustained signal playing - then you'll see the realtime power output of the device.
Photo sample below, here's me using an oscilloscope to volume match my devices (crazy experimentation of mine back then)
There are other things that you have not accounted for.
1. During DC fast charging where Q7 will draw current at 12V. Not sure if it is charging at 2A but the Q7 does top charge relatively quickly even during usage.
2. Q7's own power consumption
The power supply will send as much current at 12V as needed up to its maximum rated 12V/2A (24W). I believe you're right in that there may be some extra headroom which is always nice.
I'm an idiot I didn't think about the charging of the battery, i just tested it and it draws about 1.2A/14.4W when charging.
It still leaves about 10W of headroom.
I'm an idiot I didn't think about the charging of the battery, i just tested it and it draws about 1.2A/14.4W when charging.
It still leaves about 10W of headroom.
You can adjust your music amplitude to try, such as using 0dB,-3dB sine wave, so as to achieve the maximum power
We designed the maximum power, in our normal listening music is not used to, he is only for some extreme conditions to prepare. In order to make these extreme conditions of the output can still maintain the perfect sound performance
As some cars are designed, the maximum power how much N.m, but we only in rare cases to use it
Sorry to hear about that. Did you update the Q7 via the Windows computer? Please try to reset the Q7 when connecting it to the computer via USB.
Does the issue remain?
When and where did you buy the product? Can your seller help? If not, please send the receipt to us(support@fiio.com). Thanks in advance!
Sorry to hear about that. Did you update the Q7 via the Windows computer? Please try to reset the Q7 when connecting it to the computer via USB.
Does the issue remain?
When and where did you buy the product? Can your seller help? If not, please send the receipt to us(support@fiio.com). Thanks in advance!
Anyone having a slight jitter when playing MQA from iPhone via Tidal? At the start of every track there are two pauses/jitters (about five seconds into the song). After that it’s fine. Playing from Apple Music it’s fine. On latest firmware.
Anyone having a slight jitter when playing MQA from iPhone via Tidal? At the start of every track there are two pauses/jitters (about five seconds into the song). After that it’s fine. Playing from Apple Music it’s fine. On latest firmware.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.