[FiiO]

no no no, i think you're missing the point - the previous numbers you listed had SE and BAL values flipped i believe - there is no chance single-ended 6.35mm has 1700mw power while 4.4mm bal has 930

Dear friend,

We checked again with the engineer. The data is correct.
You will find there is a condition: THD+N＜1%. When using with 16Ω balanced headphone, the temperature will get high and THD+N＜1% will be reached easlier.

Best regards

 

[FiiO]

Has anyone managed to buy Psu Fiio PL50 120v?
It has been out of stock for months and FiiO does not restock.
The K7 Red was launched months ago and until today it has not been put up for sale, everything is with many months delay, does anyone know the reason for this?

If anyone knows of a used pl50 120v pm please.

@FiiO

Dear friend,

If everything goes well, PL50 110V edition will be in stock again at about October.

Best regards

 

[surgicaltech1984]

I'm curious. What's the best quality for plugging in a DAP? 3.5mm to coaxial. Or USB c to USB b? Output is unbalanced headphones.

 

[ahmonge]

I'm curious. What's the best quality for plugging in a DAP? 3.5mm to coaxial. Or USB c to USB b? Output is unbalanced headphones.

I’d choose USB, not because it sounds better than a S/PDIF over coaxial, but because can get higher sample rates.

 

[surgicaltech1984]

I’d choose USB, not because it sounds better than a S/PDIF over coaxial, but because can get higher sample rates.

I just went ahead and ordered both of the cheapest options of cables from Amazon. Guess I'm gonna have to save up to get some really nice balanced gold ones now so I can hookup my 650d's when they get here tomorrow.

 

[MikonJuice]

Hi, I`m having a little bit of trouble with the k7. I can`t, for the life of me, make the sound go to the speakers that I put behind. I mean... I can hear a very low volume audio coming out, but it`s just too low. The speakers work perfectly fine with my tv, but not with the fiio. help?

 

[Paco ignacio]

Are you using them on pre mode?

 

[MikonJuice]

Are you using them on pre mode?

Tried all the three modes, but result was the same. Very, very low volume in the sound.

 

[Paco ignacio]

Tried all the three modes, but result was the same. Very, very low volume in the sound.

I know it's kind of obvious but, did you check the volume levels of your source (Pc, dap, etc.)?

 

[ahmonge]

Hi, I`m having a little bit of trouble with the k7. I can`t, for the life of me, make the sound go to the speakers that I put behind. I mean... I can hear a very low volume audio coming out, but it`s just too low. The speakers work perfectly fine with my tv, but not with the fiio. help?

Please provide us with more information so that we can help you. Make and model of source and speakers, and type of connection between source and DAC and DAC and speakers (assuming the speakers are active).

 

[bassman12345]

Hi, I`m having a little bit of trouble with the k7. I can`t, for the life of me, make the sound go to the speakers that I put behind. I mean... I can hear a very low volume audio coming out, but it`s just too low. The speakers work perfectly fine with my tv, but not with the fiio. help?

May I assume those are powered speakers? I use powered speakers daily. Generally, I keep PC volume at max, and set K7 volume to about 70%.

 

[FiiO]

Hi, I`m having a little bit of trouble with the k7. I can`t, for the life of me, make the sound go to the speakers that I put behind. I mean... I can hear a very low volume audio coming out, but it`s just too low. The speakers work perfectly fine with my tv, but not with the fiio. help?

Dear friend,

Your speaker is active or passive speaker? The K7 could not drive the passive speaker directly.

Best regards

 

[Argha]

@FiiO
There are two problems that people were facing in the Original K7 1) Linear Volume Control and 2) Firmware issues - Did you guys keep these things in mind while designing the K7BT?

 

[dpump]

@FiiO
There are two problems that people were facing in the Original K7 1) Linear Volume Control and 2) Firmware issues - Did you guys keep these things in mind while designing the K7BT?

Always amazes me that people, especially those new to head-fi, ask questions that have already been answered in the thread. Search and read before asking and you may find the information you are looking for.

 

[Argha]

Always amazes me that people, especially those new to head-fi, ask questions that have already been answered in the thread. Search and read before asking and you may find the information you are looking for.

Well, I didn't find the answer after searching. Instead of writing Two sentences, you could've said Yes/No & it always amazes me that people, especially those old to head-fi have to flex all the time.