scompton
Headphoneus Supremus
- Joined
- Jan 21, 2005
- Posts
- 6,060
- Likes
- 27
ATHFan, there's a MD/CD-R Out (Rec) that you can use. It's similar to the tape out I've used with my vintage NAD.
Originally Posted by Navyblue /img/forum/go_quote.gif I am no expert on the video side, so I could be wrong on this. I know that VGA can be converted to DVI-A. HDMI can take DVI-D signal, I'm not sure if it can take DVI-A signal, my guess is it can't. If the above is true, you can only use the S-Video or component video input on the receiver. To correct my previous post, you don't need a S-Video to component video converter, you can just use an S-Video cable. Nope. At the back of your receiver there is the "FRONT" RCA jacks under the "PRE OUT" section (essentially the analog audio signal of front left and right channel), that's where you hook up with the RCA input of the headphone amp. Think of it like a water tap. In the ideal case, we have a tap sticking out of the wall, once you open it and you get water. However in your case you have another valve before your water tap. So you have to open the valve (ideally full blast) so that you can get water out of the tap. If the valve is opened half way, even if the tap is opened all the way, you'd only get half of the full blast. Personally, I wouldn't do this. If the headphone jack of the receiver is decent I'd just plug straight into it for casual listening. and I'd plug the headphone amp to the source for my serious listening. But you don't necessary hear any deterioration in sound quality, depending on your gears and ears. |
Originally Posted by scompton /img/forum/go_quote.gif ATHFan, there's a MD/CD-R Out (Rec) that you can use. It's similar to the tape out I've used with my vintage NAD. |
Originally Posted by scompton /img/forum/go_quote.gif ATHFan, there's a MD/CD-R Out (Rec) that you can use. It's similar to the tape out I've used with my vintage NAD. |
Originally Posted by ATHFan /img/forum/go_quote.gif Is this better than using the Pre Out's Front ports? |
Originally Posted by scompton /img/forum/go_quote.gif I'm not sure, but it should be a line out, not effected by volume settings like the pre out is. I also don't know what it does with multi channel sound. Hopefully, your owners manual will say what is sent to it. I've never dealt with anything other than stereo so I'm not really sure what these AV receivers do for line out and headphone out of multi channel sound. |
Originally Posted by xxbaker /img/forum/go_quote.gif i'm not sure i really agree with navyblue... the water analogy doesn't really work because the second valve that you add in between the other two doesn't only limit the sound, it can also amplify it. this means that if you turn the middle valve up all the way and then control the amount with only the valve on the end, by barely opening it water will shoot out an uncontrollable amount. |
Originally Posted by xxbaker /img/forum/go_quote.gif you'd want a line level output that hasn't been changed. the signal coming out of the headphone jack has been through an amplifier and therefore will introduce extra noise/distortion that isn't necessary. |
Originally Posted by Sherwood /img/forum/go_quote.gif Yamaha volume controls work on a plus(+) minus(-) system. The preamp section can attenuate (softer) or amplify (louder) the signal. Turn the knob to where the display reads 0.00 Db and you're getting passthrough. That being said, you're making this WAAAY too hard. You undoubtedly want to do one of two things: 1) Use the MD/CD-R out from the back panel. This is a true line-out, and is unconnected to the volume control. 2) Plug the headphones directly in to the headphone jack! It's a good jack! I've listened to it extensively, and I like it almost as much as my Millett Hybrid for low and high-impedance cans. Plus you can take advantage of Yamaha's directional processing engine if you're FPS gaming on the PS3, or listening to the surround track from movies. It works well for those purposes, though not for music. Best of luck, and enjoy your setup! |
Originally Posted by Navyblue /img/forum/go_quote.gif The water analogy is only for the sake of simplification. If you want to get legal The same goes for pre amp line out. |
Originally Posted by xxbaker /img/forum/go_quote.gif oh sorry, i thought that he was using the headphone out on the front as the input, not a line out that happened to be on the front. in that case there would be no distortion introduced as it wouldn't be passing through an amplifier |
Originally Posted by notoriousmatty /img/forum/go_quote.gif ...im using HDMI for audio and you CANT convert an analog signal to digital its still possible for me to use a headphone amp? correcT? |