Recent content by Arski
-
A
Home-Made IEMs
Thanks, it’s always good to have some reference:)- Arski
- Post #15,358
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Do you have any freq response of that setup build by yourself? I would love to see/hear your point of view (if that makes sense);)- Arski
- Post #15,356
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Thank you. I did a little mistake, it was 33 with 47 ohm resistor, not 10ohm like on the picture. I was looking for a little bit of lowend enhancement in this setup and I was hoping of getting that lowend little pushed without the resistor but I can see that this 6k like to show up as well. And...- Arski
- Post #15,355
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
I would try that setup with the yellow damper and without resistor on the 33 like that. Should working fine: How do you know that curve looks/sounds good? Or if it’s not too flat?- Arski
- Post #15,352
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Please tell me what would be your go-to curve as a reference? If you would build that setup, what would you do? I am afraid of losing a perspective in that project.- Arski
- Post #15,350
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
I got rid of the attenuation on the woofer and set orange damper on it, with smaller diameter tube. Maybe I should better put back the yellow on it?- Arski
- Post #15,349
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
I did few updates and modification to my 33&2389 circuit and came up with this result. It will be a onstage CIEM. It’s pretty flat and I can’t tell if it’s good or not, regarding to a ear freq response is it gonna be ok or harsh in the 3k area?- Arski
- Post #15,347
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
What’s gonna happen if you close the back vents? Bass drop?:D I did series/parallel connection and parallel is the one which works the best. Thanks to your suggestions SWTNATE. Btw what was your best setup for the 33 and 2389? Did you try 2389D?- Arski
- Post #15,334
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
This is looking interesting, how about the grinding stone? Are you using it too?- Arski
- Post #15,329
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
You mean something like this?- Arski
- Post #15,324
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Thanks! One more question. How is your approach in rounding the edges of the faceplate? Is there any tool that can help to do it even?- Arski
- Post #15,322
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Ok thanks, that was because I had a resistor and capacitor connected as a Lopass on my woofer but recently I decided to get rid of the cap and that 2 resistors is a left over, good point Piotrus, thanks. I’ll do a better Lopass with the damper, I hope that’ll help:)- Arski
- Post #15,321
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Thanx I’ll try that one. Btw I am a huge fan of your work here, your finishing and final look of your iems are outstanding! Btw do you have any hint to put a finish lac on the plate using a brush to get the super flat/smooth surface? I am using Dreve Lac 3 for finish.- Arski
- Post #15,316
- Forum: DIY (Do-It-Yourself) Discussions