- Joined
- Jul 11, 2009
- Posts
- 2,926
- Likes
- 716
Yes. Sounds good. The he1000 is not particularly difficult to drive.
No not too much, rather the opposite: it's far below that of the tubes the amp is designed for. The 6BX7 draws 40mA and the 6SN7 nominally draws 9mA per section.
You aren't going to hurt anything, I'm just saying it might not sound good when you try it.
My trusted source for adapters is 2359glenn who can be found on this forum. He's pretty busy these days with requests so I have no idea how what kind of wait time there is I'm afraid.
I would recommend trying the 6BX7 before exploring lots of tubes. They sound wonderful and are pretty cheap to get ahold of. As long as the amp has enough volume that is, though I hear the design was changed a bit recently to resolve that issue. I'd love to know the details of that actually. I'm no amp designer but I've absorbed some knowledge over the years and it seems to me that the obvious way to give the amp more gain would be to change the design so each section of the 6SN7/6BX7 was no longer parallel wired but instead are each treated as a separate gain stage. This would definitely give the amp more volume, but would reduce it's ability to drive difficult to power headphones and would have a slightly negative effect on the amps resolution. But that's not necessarily what was done, it could have been changes in the transformers or any number of other design tweaks. If you have any communication with Drew or Dennis when you order you should ask and see if they'll tell you.
Has anyone used the Inspire IHA-1 to drive the HE-1000's?
Or, do you know of a thread that addresses the combination?
Thanks...
In order to drive my HD800 I have use my volume knob at ~3-4 o'clock. Is this normal?
This is normal.
So, why would this be normal? It is because no caps and resistors design?
So, why would this be normal? It is because no caps and resistors design?
It's because there is only one amplification stage in the amp. Nearly all tube amplifiers have two (some have three or more). Let's take the Icon Audio HP-8 for example, a fairly similar amp in feature and price. It has a 12AX7 first stage and 6SN7 second stage. That's a gain factor of 120 multiplied by 20 for a total gain of 2,400. This gets reduced by a certain factor in the transformers but it's still a lot, and the reason why you can't really turn the volume in that amp past 9 o'clock without it blaring.
Contrast that with the IHA-1 which ONLY has a 6SN7 stage for amplification. Further more each section of the tube is in parallel to increase current drive so the total gain is that of a single section, which is 20. You can see the effect of changing output gain by using 6BX7 tubes in the amp (whose gain is only 10), as you need to go a couple of clicks higher to get the same volume. In the case of high impedance phones or ones with low sensitivity, you end up running out of clicks.
The reason the designer did this was to maximize sound quality. A single stage amp has very low distortion and is very transparent sounding, but the drawback that comes with it is this inflexibility. The amp only really likes high sensitivity headphones, and planars whose sensitivity is high enough to get the volume you need. It's a major reason why the amp isn't more popular I'm guessing. I think at some point we'll see Dennis do a V2 of this amp and he'll go with another tube choice with higher gain to get around this problem. The 6SN7 is not a very high gain tube and is normally used as a driver stage, here it's both driver and output.
An easy solution would be to make each section of the 6SN7 a separate gain stage, then you have a gain of 20 x 20 = 400. But the highly transparent nature of the amp would suffer and there would be less ability to drive low impedance high current loads. So either design choice is a trade-off. The designer went with performance over flexibility.
It's because there is only one amplification stage in the amp. Nearly all tube amplifiers have two (some have three or more). Let's take the Icon Audio HP-8 for example, a fairly similar amp in feature and price. It has a 12AX7 first stage and 6SN7 second stage. That's a gain factor of 120 multiplied by 20 for a total gain of 2,400. This gets reduced by a certain factor in the transformers but it's still a lot, and the reason why you can't really turn the volume in that amp past 9 o'clock without it blaring.
Contrast that with the IHA-1 which ONLY has a 6SN7 stage for amplification. Further more each section of the tube is in parallel to increase current drive so the total gain is that of a single section, which is 20. You can see the effect of changing output gain by using 6BX7 tubes in the amp (whose gain is only 10), as you need to go a couple of clicks higher to get the same volume. In the case of high impedance phones or ones with low sensitivity, you end up running out of clicks.
The reason the designer did this was to maximize sound quality. A single stage amp has very low distortion and is very transparent sounding, but the drawback that comes with it is this inflexibility. The amp only really likes high sensitivity headphones, and planars whose sensitivity is high enough to get the volume you need. It's a major reason why the amp isn't more popular I'm guessing. I think at some point we'll see Dennis do a V2 of this amp and he'll go with another tube choice with higher gain to get around this problem. The 6SN7 is not a very high gain tube and is normally used as a driver stage, here it's both driver and output.
An easy solution would be to make each section of the 6SN7 a separate gain stage, then you have a gain of 20 x 20 = 400. But the highly transparent nature of the amp would suffer and there would be less ability to drive low impedance high current loads. So either design choice is a trade-off. The designer went with performance over flexibility.
Sooo... You are telling me high imedance phone like the HD800s is not a good match for this amp, correct?
Not at all, I'm just answering your question as to why you feel you have to turn the volume up so high. FWIW I often listen to my Inspire with the volume wide open at max with my LCD-2s. It sounds fantastic, there just isn't any extra volume leftover for music that was recorded at a low level such as some classical pieces.
New message from: radioman731 (828) | |
|