Any advice on shifting the pinna gain peak on RAB-32257 from 4k down to 3kHz?
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
Home-Made IEMs
- Thread starter Bilavideo
- Start date
swtnate
500+ Head-Fier
There are all sorts of info already posted in this thread regarding RAB. Start with the proper zobel network. Adjust tube length and damper accordingly.Any advice on shifting the pinna gain peak on RAB-32257 from 4k down to 3kHz?
longer tubingAny advice on shifting the pinna gain peak on RAB-32257 from 4k down to 3kHz?
justsomesonyfan
Headphoneus Supremus
- Joined
- Sep 24, 2013
- Posts
- 1,587
- Likes
- 1,920
value plummeted it seemsI saw prices for $199-250-500$ depending on model
justsomesonyfan
Headphoneus Supremus
- Joined
- Sep 24, 2013
- Posts
- 1,587
- Likes
- 1,920
these look crazy ngl.. serious beauties, would be interested had I not found my endgamejust look at these beauties
as far as I know these are AMT full range flagships
they are expensive, but I have seen cheaper models from the same manufacturer ($200-250)
and oxygen here for 500
https://www.head-fi.org/classifieds/bionic-sound-oxygen-amt-drivers-hi-fi-from-ukraine.56972/
justsomesonyfan
Headphoneus Supremus
- Joined
- Sep 24, 2013
- Posts
- 1,587
- Likes
- 1,920
tell you what, from the 3 pairs I had 2 were comfy the third was NOT. so do take cautionyes, and they still sell for less than 1000....
I'm thinking of buying myself a pair
I haven't seen many reviews for them, have you owned any and which ones fit?tell you what, from the 3 pairs I had 2 were comfy the third was NOT. so do take caution
justsomesonyfan
Headphoneus Supremus
- Joined
- Sep 24, 2013
- Posts
- 1,587
- Likes
- 1,920
I owned three, I don't know the names, there were two hybrids which were 1dd/1amt, and those fit well, and one amt only, which did not fit very well.I haven't seen many reviews for them, have you owned any and which ones fit?
Got my IEC-711 clone calibrated, IEC60318-4. Measurements of KZ ZSX and my DIY 10mm planars, with physical tuning only. The highs are a little shimmery on the planars but details is there, and with the right tips and good seal, sibilance is minimal. I posted dayton Imm-6 measurements earlier in the thread, these planars are my daily drivers. I might almost have more listening time than build time at this point, a few years later
Edit: it is ZX ZAX, not ZSX. Just there for a comparison on dB level.
Edit: it is ZX ZAX, not ZSX. Just there for a comparison on dB level.
Last edited:
Hi Guys, i need a help with my Blon blo3 iem.
I removed the nozzle filters because of dust accumulation and sound is not coming properly in one side and i lost the stock filters.I'm using foam used for microphone cover foam, but even after that I'm hearing sibilance. I don't know how to control sibilance.i can't order nozzle filters from AliExpress, because it was banned in my country. Is there any other way to reduce sibilance?
I removed the nozzle filters because of dust accumulation and sound is not coming properly in one side and i lost the stock filters.I'm using foam used for microphone cover foam, but even after that I'm hearing sibilance. I don't know how to control sibilance.i can't order nozzle filters from AliExpress, because it was banned in my country. Is there any other way to reduce sibilance?
Last edited:
Find some open cell foam sheets, maybe 1/4" thick maximum. The microphone cover may be too thin, try multiple pieces. Cut small circles of the foam, and insert into nozzle. Try different types of foamHi Guys, i need a help with my Blon blo3 iem.
I removed the nozzle filters because of dust accumulation and sound is not coming properly in one side and i lost the stock filters.I'm using foam used for microphone cover, but even after that I'm hearing sibilance. I don't know how to control sibilance.i can't order nozzle filters from AliExpress, because it was banned in my country. Is there any other way to reduce sibilance?
StephenJames
New Head-Fier
Quick question for anyone who's 3d printing their shells with standard resin, and then giving them a final coat of fotoplast lack3.
Are you sanding your shells before adding the lack3? Or are the print layers small enough, that the lack3 will fill them in and still give a smooth finish.
I'm using a photon mono 4k which can get down to a pretty fine resolution. I sanded my last pair a little bit, but am I just making more work for myself?
Are you sanding your shells before adding the lack3? Or are the print layers small enough, that the lack3 will fill them in and still give a smooth finish.
I'm using a photon mono 4k which can get down to a pretty fine resolution. I sanded my last pair a little bit, but am I just making more work for myself?
hi guys , where you all buying drivers in Usa ? Cuz i buy at aliexpress, and it take forever to get in California.
Which company sends faster?
Thank you
Which company sends faster?
Thank you
JASON99
New Head-Fier
Hi bros
Recently, i’m making own iem.
But the its Fr graph little strange, so i need your help. As the graph , 0~200hz are too deep compare to other iems (n5005, t9ie).
Can you give me a advice about this situation.
Thank you!
Picture link. https://ibb.co/hszBHhL
Recently, i’m making own iem.
But the its Fr graph little strange, so i need your help. As the graph , 0~200hz are too deep compare to other iems (n5005, t9ie).
Can you give me a advice about this situation.
Thank you!
Picture link. https://ibb.co/hszBHhL
Hi bros
Recently, i’m making own iem.
But the its Fr graph little strange, so i need your help. As the graph , 0~200hz are too deep compare to other iems (n5005, t9ie).
Can you give me a advice about this situation.
Thank you!
Picture link. https://ibb.co/hszBHhL
What's the config of your iem?
Users who are viewing this thread
Total: 14 (members: 0, guests: 14)