JEHL
1000+ Head-Fier
Another noob question. Does something like Elegoo Mars series work for printing housings?
Get Anycubic Photon Mono, cheaper and works perfectAnother noob question. Does something like Elegoo Mars series work for printing housings?
Dude why don't you make a planar hybrid? Like DD tuning is hard, I would put that effort in tuning a planar 10mm driver, tunes the same wayThanks for the information!
I found a really cheap impedance box on AliEx I wonder if it is ok?
https://a.aliexpress.com/_mOIG9b
I also have the feeling it would be rather hard to modify or build a hybrid set with DD. What are the cons from your experience?
I tried using a hairdryer and it actually worked, not too hot I could still hold the heated driver with my fingers. Acetone will actually melt the plastic, won't it?
Since you mentioned using the ZST as a mold, I think you may check out the CCA CSN. It is really spacious and quite fun to mod.
Try this linkI can't open the link.
Good for you then. I always had a bad time with heat and DD hahaha. Not really, I think some plastics can be dissolved by Acetone but not all. If it does, then it will be easier to pry off the driver, won't it?
I don't use other shells anymore, I abandoned the ZST mold years ago. I now create my own shells and print them out or do the traditional pour method.
I am not actually a fan of planar driver. I had the Tri i3 and the **** MT100 Pro and I think I prefer DDs and BAs.Dude why don't you make a planar hybrid? Like DD tuning is hard, I would put that effort in tuning a planar 10mm driver, tunes the same way
I'ld suggest the Finale2, it's an easy build with outstanding detail. It's a bit light on the bass for me, but it matches your description very well.here for a relatively easy setup with good detail and a relatively neutral soundstage (quite sensitive to bass and high frequencies).
Thank you very much; these are some A-grade instructions. Definitely will give it a try to build something like thisI'ld suggest the Finale2, it's an easy build with outstanding detail. It's a bit light on the bass for me, but it matches your description very well.
Diagram: https://crcit.net/c/7d75c8a5
See here for a comparison of a few I built:
https://www.head-fi.org/threads/home-made-iems.430688/page-627#post-15023250
And me lol, just orderedthe E50DT0005 is now in stock on Aliexpress from soundlink Because of me.
I'll use it to experiment@kkugel btw u can add the E50DT0005 to your estat build. That's you wanna do ?
It could be an amazing build.
Hi, I would like to start with the BS6, but the 10013 is hardly available. Can I combine two Bellsing 30017s and a Knowles 30008 (Bellsing DTEC is hard to get...)?I'ld suggest the Finale2, it's an easy build with outstanding detail. It's a bit light on the bass for me, but it matches your description very well.
Diagram: https://crcit.net/c/7d75c8a5
See here for a comparison of a few I built:
https://www.head-fi.org/threads/home-made-iems.430688/page-627#post-15023250
It's actually not ER4 as Fyre did a response, looks like, they added less resistance to ED and that's why uppermid didn't rise as ety didAnyway, has anyone seen the KB EAR Neon yet? Seems like an attempt at making a more affordable ER4 priced at $50. And reviews make it seem like it's very close to the ER4SR if you don't mind the deep insertion.
Makes me wonder how hard'll be to one up what I can only assume is a deceptively well implemented ED-29689 at $50.