Does anyone know what the impedance of the Parterre is? Are they considered low or high impedance iems? Thanks!
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
FitEar Parterre (パルテール) Thread
- Thread starter Sopp
- Start date
castleofargh
Sound Science Forum Moderator
- Joined
- Jul 2, 2011
- Posts
- 10,443
- Likes
- 6,063
I've never seen a value about that, but they're still pretty low IMO(or at least with a big variation accross frequencies) as adding resistors does change the signature pretty significantly. and I personnaly didn't like the change.
but the sensitivity is much lower than the 334 (Parterre would be normal for an IEM, and 334 super sensitive).
but the sensitivity is much lower than the 334 (Parterre would be normal for an IEM, and 334 super sensitive).
CosmicHolyGhost
Exhaustively burning holes in his wallet
- Joined
- Jun 10, 2013
- Posts
- 3,143
- Likes
- 246
Yah. The sensitivity of Parterre is good for using portable source with higher power like HM901 or X5
Tg334 and their ciem are way too sensitive in comparison...
Where can one buy resisitors btw?
Tg334 and their ciem are way too sensitive in comparison...
Where can one buy resisitors btw?
I've been doing a lot of tip rolling with mine. Has anyone had the titanium nozzle loosen from the body? They look very secure, but thought I would ask. Thanks.
Yah. The sensitivity of Parterre is good for using portable source with higher power like HM901 or X5
Tg334 and their ciem are way too sensitive in comparison...
Where can one buy resisitors btw?
I've found Etynomic type resistors on Ebay, from Hong Kong.
castleofargh
Sound Science Forum Moderator
- Joined
- Jul 2, 2011
- Posts
- 10,443
- Likes
- 6,063
Where can one buy resisitors btw?
I use a few of those http://www.ebay.fr/itm/ETYMOTIC-ER4P-TO-ER4S-RESISTOR-ADAPTOR-3-5MM-PLUG-/290372905689?pt=US_MP3_Player_Cables_Adapters&hash=item439b92ead9
you can ask for whatever value you like (I asked for 3ohm, 5, 30 and 100).
as a warning, the 334 is ok with those, but the parterre didn't sound any good with more impedance added to the source. I think we talked about that some pages back and all agreed that the parterre was best served as is.
CosmicHolyGhost
Exhaustively burning holes in his wallet
- Joined
- Jun 10, 2013
- Posts
- 3,143
- Likes
- 246
Thanks, guys. I have a dumb question, will i get my vol room if i use a high impedance adapter for my c435 as they are too sensitive...?
castleofargh
Sound Science Forum Moderator
- Joined
- Jul 2, 2011
- Posts
- 10,443
- Likes
- 6,063
yes but you will probably ruin the c435's signature long before benefiting from the volume getting lower.
in your shoes I would just accept the fact that some sources can't be used with this IEM and would look for an amp with digital volume control.
in your shoes I would just accept the fact that some sources can't be used with this IEM and would look for an amp with digital volume control.
I've been very impressed with the low floor noise of the Pure II. I'd make it a strong consideration for sensitive iem's.
CosmicHolyGhost
Exhaustively burning holes in his wallet
- Joined
- Jun 10, 2013
- Posts
- 3,143
- Likes
- 246
yes but you will probably ruin the c435's signature long before benefiting from the volume getting lower.
in your shoes I would just accept the fact that some sources can't be used with this IEM and would look for an amp with digital volume control.
Thanks for the advice.
I've gotten good fit and sound with large tips/shallow insertion and medium tips/deeper insertion. Parterre's look like they are maybe built for deeper insertion than I've been using. Just wondering what insertion depth other owners use?
CosmicHolyGhost
Exhaustively burning holes in his wallet
- Joined
- Jun 10, 2013
- Posts
- 3,143
- Likes
- 246
I've gotten good fit and sound with large tips/shallow insertion and medium tips/deeper insertion. Parterre's look like they are maybe built for deeper insertion than I've been using. Just wondering what insertion depth other owners use?
I use medium sized ortofon tips with deeper insertion to obtain good isolation and SQ. I would pull my ears out to ensure inserting correctly.
mcluzar
New Head-Fier
- Joined
- Dec 3, 2013
- Posts
- 17
- Likes
- 10
I've gotten good fit and sound with large tips/shallow insertion and medium tips/deeper insertion. Parterre's look like they are maybe built for deeper insertion than I've been using. Just wondering what insertion depth other owners use?
Just got my Parterre recently - tried all of the stock FitEar tips and none of them gives me good fit and sound.
I am currently using the smallest Comply T200 tips, and it gives me really good fit.
Thanks, guys. I have a dumb question, will i get my vol room if i use a high impedance adapter for my c435 as they are too sensitive...?
Hello
Here's an impedance adaptor you should try
I use it with my Cavalli LAu for sensitive IEMs such a FitEars. Lowers level by 14db if I remember correctly...................
CosmicHolyGhost
Exhaustively burning holes in his wallet
- Joined
- Jun 10, 2013
- Posts
- 3,143
- Likes
- 246
Hello
Here's an impedance adaptor you should try:wink_face: .
I use it with my Cavalli LAu for sensitive IEMs such a FitEars. Lowers level by 14db if I remember correctly...................
Thanks! I was meaning to buy this from Fujiya last year but they did not have Wagnus S in stock. So...
Users who are viewing this thread
Total: 2 (members: 0, guests: 2)