You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
DIY Earbuds
- Thread starter gwompki
- Start date
assassin10000
Headphoneus Supremus
I got a of M0 shells with a faulty connector(which are being replaced by the seller no sweat) but I want to try and salvage them by cutting off the connector and soldering in some DIY drivers. 15.4mm drivers have been suggested to me by furyossa but after some research it appears 15.4mm DIY drivers are the standard for mx500 shells? I measured the m0 shells (pics below) and it is significantly smaller than a mx500, with smabat's 15.4mm drivers needing a large lip to fit the smaller shell. Measurements are a bit tricky because the shells use a compressible o-ring to secure the drivers with the measured value depending on how much force I applied. So I measured sambat's drivers(which I can't plug in) and got a value of 13mm on the inside as shown in the picture.
Does anyone know what form factor of DIY drivers(if any) will fit these shells?
I think only other hope would be maybe bypassing the female connector soldered onto one of the drivers sold by smabat?
The driver needs to be detached from the ring. The driver & cover is probably 15.4mm, where as the ring that snaps into the cover is 13mm I.D.
You can see the smooth black metal or plastic adapter ring in your photo where you measure the 13mm.
Hey, so I just got this shell from NSC and the composite Beryllium driver. But what is this connection? How to use mmcx with this?
Looks like its there but in upside down. Pop the gold looking piece out, that is the MMCX connector.
TheLastAurora
New Head-Fier
Doesn't seem so... Maybe they sent me the wrong version?The driver needs to be detached from the ring. The driver & cover is probably 15.4mm, where as the ring that snaps into the cover is 13mm I.D.
You can see the smooth black metal or plastic adapter ring in your photo where you measure the 13mm.
Looks like its there but in upside down. Pop the gold looking piece out, that is the MMCX connector.
Attachments
assassin10000
Headphoneus Supremus
That's both sides clipped together.Doesn't seem so... Maybe they sent me the wrong version?
TheLastAurora
New Head-Fier
Lmao, yes, thank you! They were so tight that I though that you couldn't remove that, but yeah.That's both sides clipped together.
https://www.aliexpress.com/item/1005001611157987.htmlLmao, yes, thank you! They were so tight that I though that you couldn't remove that, but yeah.
TheLastAurora
New Head-Fier
Just wow! The composite BE driver and the metal shell from NSC. I tried stock with no tuning at all but there was too much bass bleeding to mids and too much bass. Tried foam and terrible stage and no bass and texture. But microporous tape does magic. The bass now is punch and very present (bassheads will like it), has a nice texture, the mids have body, and the highs are laid back. I really much like it. Has a nice touch of warmth to it. I would say this set is L shaped. Would pick 100x times these over the 130 LCP. Wil order more.
Last edited:
re23071998
New Head-Fier
great build!Just wow! The composite BE driver and the metal shell from NSC. I tried stock with no tuning at all but there was too much bass bleeding to mids and too much bass. Tried foam and terrible stage and no bass and texture. But microporous tape does magic. The bass now is punch and very present (bassheads will like it), has a nice texture, the mids have body, and the highs are laid back. I really much like it. Has a nice touch of warmth to it. I would say this set is L shaped. Would pick 100x times these over the 130 LCP. Wil order more.
which drivers are these?
also wdym by microporous tape?
TheLastAurora
New Head-Fier
https://a.aliexpress.com/_mKuPqH5great build!
which drivers are these?
also wdym by microporous tape?
Micropore or microporous tape. I've used tons of times with IEMs before, but works flawlessly to reduce bass duration and quantity without changing the highs response by much.
Last edited:
re23071998
New Head-Fier
how did you put that in? just tape it behind the drivers?https://a.aliexpress.com/_mKuPqH5
Micropore or microporous tape. I've used tons of times with IEMs before, but works flawlessly to reduce bass duration and quantity without changing the highs response by much.
I used this in which I made a few holes with a needlehow did you put that in? just tape it behind the drivers?
Attachments
TheLastAurora
New Head-Fier
As @jeejack has shownhow did you put that in? just tape it behind the drivers?
Last edited:
re23071998
New Head-Fier
these drivers just came in and they dont fit my jcally housing, sadly :vHigh Resolution 15.4mm Speaker Unit for MX760 DIY Heavy Bass Earphones DIY 10pcs
https://a.aliexpress.com/_mry9ufv
currently still with the 130 berry, quite bassy drivers on this housing
Last edited:
For 130 bery drivers i use silver MX500 shell (Tingo TC 200). For MX760 drivers you can use also MX500 shellthese drivers just came in and they dont fit my jcally housing, sadly :v
currently still with the 130 berry, quite bassy drivers on this housing
Attachments
re23071998
New Head-Fier
hmm, mine do not seem to fit with mx500 shellFor 130 bery drivers i use silver MX500 shell (Tingo TC 200). For MX760 drivers you can use also MX500 shell