Recent content by tubesmuggler
-
Reply to review by 'tubesmuggler' on item 'IMS Hybrid Valve Headphone Amplifier (HVA)'
Hey this is an interesting little amp. thetubestore has them so I might give one a try http://www.thetubestore.com/Parts-Accessories/Amps-and-Amp-Kits/Hybrid-Valve-Headphone-Amp- tubesmuggler
- Head Gear rating reply
-
Bantam DAC - Noise issue
Thanks guys. Nullstring I'll try a different PC tonight. I'm very new to this and don't know if I'm really setting up my "system" right. I found Analog Devices software on my PC called SoundMAX. I never noticed it before, but I've never really looked. Anyway, I noticed that it's Master Volume...- tubesmuggler
- Post #6
- Forum: DIY (Do-It-Yourself) Discussions
-
Bantam DAC - Noise issue
Thanks for your reply TomB. The grounding is solid. I will try to get some pics by tomorrow, maybe tonight.- tubesmuggler
- Post #3
- Forum: DIY (Do-It-Yourself) Discussions
-
Bantam DAC - Noise issue
I have what I think is a properly assembled Bantam DAC with upgrade PS filter cap. It is extremely noisy though. Is this a sign of a build error or is this common with USB powered DACs? My PC seems fine and recognized it correctly. I've played it for a couple hours but the noise is bad. The...- tubesmuggler
- Thread
- Replies: 6
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Quote: Originally Posted by regal How do you like the copper AmpOhm's ? I just ordered a pair. . I'll let you know. I haven't played music through this puppy yet.- tubesmuggler
- Post #1,221
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
OK, I'm all done....at least for now. Everything checks out and the Bantam DAC fit nicely in the back with some sweet AmpOhm Copper Foil/PIO caps. Hopefully I can start burn-in tomorrow. One thing I can't figure out is why access to the B+ trimmer is needed? Why drill the hole to adjust B+?- tubesmuggler
- Post #1,219
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Got it! The ZN Mcap was damaged/shorted out. I removed that and everything was pretty much good. Unfortunately that leaves me with crappy Solens because I can't get anything else to fit. The Auricap leads are too fat for the pcb holes. How do the Wima's sound compared to Solens? Should I just...- tubesmuggler
- Post #1,215
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
No dice. I've just replaced Q1 and Q2 and the results remain unchanged. Voltage measured across R2 is 300mV, across R3 is 330mV. I believe it should be 220mV and 230mV or so.- tubesmuggler
- Post #1,214
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
I've taken some more measurements: Pin1 = 36V Pin6 = 16V Tail current is set and stable. The Rp is 18K as required. What's the next step? New BC560C transistors??- tubesmuggler
- Post #1,212
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Hey guys. I figured out the problem. I had the R10's installed on the R12 pads and visaversa! Oooops.. That's all fixed up now and the buffers are set correctly. Unfortunately I'm on to the next problem. The difference between TB+L and TPL is about 19V. However the TB+R and TPR is WAY off...- tubesmuggler
- Post #1,211
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
I've started the intial setup procedure. The PS is fine. I've moved on and jumpered J1 and J2. Unfortunately I can't set the Buffers. I'm aiming for 220mV across R10L and R10R, but the lowest I get is 280mV. At start up they measured around 450mV... Any idea's what to check? TIA!!- tubesmuggler
- Post #1,208
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Me again. I noticed the supplied RCA jacks are not the insulated type so they will be grounded at the rear panel. Is there still a need to run a ground from the RCAs to the ground lug on the input terminal strip, or can I just run the L and R channel leads up to the input terminal strip? And...- tubesmuggler
- Post #1,205
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Thanks for your input pixeljedi. I think I'll do it the standard way. Then figure out a way to mount the Bantam dac or skip it. I'd rather have a 24bit dac anyway.- tubesmuggler
- Post #1,203
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Unlike the suggested layout from the Soha II webpage, I think I'm going to mount the toroidal PT closer to the PCB so the Ac inlet and switch can mount on the far side of the rear panel - away from the audio inputs. This also make more room for the Bantam DAC Does anyone think the Avel toroid...- tubesmuggler
- Post #1,201
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
I'm back... Thanks for your help guys. I got the upgraded Neutrik headphone jack and I'm trying to get the front panel layed out right for it. It looks to me like the 3-pin connector I soldered onto the board there will be in the way. I assume I can remove that and then wire the Neutrik...- tubesmuggler
- Post #1,199
- Forum: DIY (Do-It-Yourself) Discussions