Recent content by danspy
-
Knowledge Zenith (KZ) impressions thread
ok my bad.- danspy
- Post #48,665
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
why you need equitation if the sound quality is more than sufficient?:ksc75smile:- danspy
- Post #48,656
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
looks good, i just ordered one. i was searching for aptx TWS for a wile now.- danspy
- Post #48,652
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
hello, i just got the ZS10 pro, wow the sound aggressive in the uppermids. a 2mm piece of porous foam under the metalcap in the nozzle and they sound like the ZS5 with a little more details and better center.- danspy
- Post #48,650
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
nice can you ship to Thailand? i can get them next day free shipping.:L3000: but are the V1,s i don't no jet.- danspy
- Post #44,018
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
thank you. i got the v1 about a week after lunch, but i damaged them in modding.- danspy
- Post #44,016
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
Hi. A quick question about the KZ ZS5 . Are all the Full box editions V1,s ?- danspy
- Post #44,013
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
The size of Driver responds mostly to SPL (Volume of sound) a small Driver needs less Air volume to produse low frequencies.- danspy
- Post #18,167
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
The mid BA housing just wood need a tiny Pinhole to contribute, and the sub-bass DD does not even to be open to the port to contribute.- danspy
- Post #18,162
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
The RMAA (RightMark Audio Analyzer) Source and Audio Device Measurement Thread [Overview of Measurements in Post #3, Tutorial in Post #2]
Sony XA + KZ ZS5 And KZ ATE The Sony XA did not work with just the soundcard load, so i used the mild 16Ohm Load of the KZ ATE. The heights on this Phone Sound amazingsingly Crisp and Detailed without getting Aggressive at all, Amplified with Low OutputImpedance of course. OutputImpedance...- danspy
- Post #180
- Forum: Sound Science
-
Knowledge Zenith (KZ) impressions thread
5 Ohm and below should be OK.- danspy
- Post #18,063
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
The RMAA (RightMark Audio Analyzer) Source and Audio Device Measurement Thread [Overview of Measurements in Post #3, Tutorial in Post #2]
Avantree Clipper Pro (Bluetooth 4.2 aptx low latency clip-on) Not bad for Bluetooth, the sound is a bit cramped at the topend because of the high frequency filter. The Output Impedance is abut 5 Ohm. Frequency response Frequency response + KZ ZS5 THD + Noise (at -3 dB FS) Noise level...- danspy
- Post #178
- Forum: Sound Science
-
Knowledge Zenith (KZ) impressions thread
Like the ZST the ZS5 needs Low outputimpedance to really shine- danspy
- Post #18,034
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
The RMAA (RightMark Audio Analyzer) Source and Audio Device Measurement Thread [Overview of Measurements in Post #3, Tutorial in Post #2]
Hi Fiio A1 Frequency response Frequency response + KZ ZS5 Locking Good! Noise level + KZ ZS5 The Noise Locks even better den Unloaded! THD + Noise (at -3 dB FS) Noise level Stereo crosstalk Greetings Dan- danspy
- Post #176
- Forum: Sound Science
-
Knowledge Zenith (KZ) impressions thread
The ZST is a Diva. My Creative Sound Blaster X-Fi HD with 40 Ohm output Impedance, is not able to drive them properly.- danspy
- Post #15,374
- Forum: Portable Headphones, Earphones and In-Ear Monitors