[FiiO Willson]

Hi - I'm facing an issue in DAC mode where the device is going in to its temporary power off mode (requiring the 2 second startup silence) after each song - so the start of each song is cut off entirely. Using SPDIF-IN at 24/96. I read a reply a few weeks ago from a Fiio account saying that this shouldn't be the case unless you physically mute the source the audio is coming from, but I haven't been able to find a fix. Anyone else experiencing this? I definitely think it's a firmware issue.

Hello. I think you may select USB and SPDIF input at the same time and no priority selected?
I can send you a new Firmware for test.
Please check your message.

 

[FiiO Willson]

Hi, I'm looking for a Bluetooth transmitter for my Audioquest Dragonfly Cobalt. I have Audio-Technica ATH-m50xBT and 1more Stylish True Wireless headphones. Will the device be able to work with both these pairs of headphones at the same time? (normal and True Wireless at the same time) Will the dragonfly have any effect on the sound coming from this device?

The device isn't available in my country (Poland). Is it safe to buy this product on Aliexpress?

I think it should work fine
You can buy from our officially approved shops, this is safe.

https://es.aliexpress.com/item/1005...earchweb0_0,searchweb201602_,searchweb201603_

 

[johnston21]

I can send you a new Firmware for test.

Is the new Firmware with changes? If so, I’d be happy to test.

 

[Dyzson]

I think it should work fine
You can buy from our officially approved shops, this is safe.

https://es.aliexpress.com/item/1005...earchweb0_0,searchweb201602_,searchweb201603_

" Sorry, this item is no longer available! "

Will there be no problem with synchronising these 2 pairs of headphones? One pair only supports AptX, the other AptX HD and I have the impression that one pair can interrupt because of this. I have already tested cheap devices from Aliexpress with the CSR8675 and CSR8670 chip. Most of them didn't want to pair with 2 pairs of headphones and when they did, it interrupted the sound.

Ps. BTA30 doesn't have an analogue input, so it cannot be used as a transmitter for Dragonfly Cobalt (only has a jack output).

 

[FiiO Willson]

Is the new Firmware with changes? If so, I’d be happy to test.

A slight improvement to the connection. However, a more complete firmware will be released later, the firmware I have here is only an improvement for the dropout problem with optical or coaxial connections

 

[FiiO Willson]

" Sorry, this item is no longer available! "

Will there be no problem with synchronising these 2 pairs of headphones? One pair only supports AptX, the other AptX HD and I have the impression that one pair can interrupt because of this. I have already tested cheap devices from Aliexpress with the CSR8675 and CSR8670 chip. Most of them didn't want to pair with 2 pairs of headphones and when they did, it interrupted the sound.

Ps. BTA30 doesn't have an analogue input, so it cannot be used as a transmitter for Dragonfly Cobalt (only has a jack output).

The BTA30 supports the pairing of 2 devices at the same time, but ultimately only in the same format.

 

[johnston21]

A slight improvement to the connection. However, a more complete firmware will be released later, the firmware I have here is only an improvement for the dropout problem with optical or coaxial connections

Thank you, and happy to wait as my only wired input is optical from a SONY TV and I’m not experiencing the drop-outs.

 

[frix]

Hi, I'm interested in the BTA30. Does it have some kind of bypass mode when my setup is as following: TV -> optical_IN -> BTA30 -> optical_OUT -> Speaker Amp. The intention is to switch easily between BT headphone and my speaker setup.

 

[rev92]

Hi guys, here's our take on Fiio BTA30 - it's a great little device!

https://ear-fidelity.com/2021/01/06/fiio-bta30/

 

[rapindrive]

Tengo un problema con el dispositivo. Solo me conecta con mi sony xm4 por SBC, no tengo forma de obtener audio transmitido por LDAC desde el dispositivo. Lo tengo conectado al PC por cable óptico.

 

[rapindrive]

Hi,

That is a good reason to me indeed.
Especially as Sony headphones are popular.

Regards.

Have you managed to connect the sony xm4 via LDAC? a greeting

 

[nikobland]

I have a problem with the device. It only connects me with my sony xm4 by SBC, I have no way to get audio by DAC transmitting from the device. I have it connected to the PC by optical cable.

Hi,

I finally got this to work. Make sure that the Headphones app is set up so that you are not allowing two devices to connect to the headphones at the same time. The BTA30 light should go a very slight shade of purple.
Let us know if it works!

 

[FiiO Willson]

Hi, I'm interested in the BTA30. Does it have some kind of bypass mode when my setup is as following: TV -> optical_IN -> BTA30 -> optical_OUT -> Speaker Amp. The intention is to switch easily between BT headphone and my speaker setup.

Hi
Bypass mode is not supported, are you using this to use both headphones and speakers and then you want to listen to either one to hear the sound?
Could you share your idea so that we can evaluate whether to add this feature to our further products?

 

[rapindrive]

Hi,

I finally got this to work. Make sure that the Headphones app is set up so that you are not allowing two devices to connect to the headphones at the same time. The BTA30 light should go a very slight shade of purple.
Let us know if it works!

It had the configuration as you indicated. It seems like a magic thing but now it works when you turn it on again! The light looks white, that indicates LDAC connection, it is a wonder for my ears. I equalize with the app of my sound card on the PC, and deactivate the equalization of the xm4 in its application. If I have a problem I will comment on it. Thanks a lot.

 

[frix]

Hi
Bypass mode is not supported, are you using this to use both headphones and speakers and then you want to listen to either one to hear the sound?
Could you share your idea so that we can evaluate whether to add this feature to our further products?

Yes, I want to use the BTA30 in between my Spdif signal chain. During daytime I would like to use my speakers. So a bypass mode would be really usefull. Bypassing the spdif signal to my speaker amp. During nighttime when the child sleeps I would like to use my headphones and disable bypass.