Recent content by Sergedc
-
Reply to review by 'Sergedc' on item 'Sennheiser IE 900'
@freeryder05 Could you share you EQ config?- Sergedc
- Head Gear rating reply
-
E1DA DACs Discussion Thread (PDV2, 9038S, 9038D, 9038X, HiFiToy, HPToy)
On PD V2, there was talk of a hiss with very high sensitivity IEM. Mine are 119 dB (36 Ohms), and I do have problem on older DAC with headphone output. Does anyone know if this was solved on the PD V2.1? Or is the hiss with high sensitivity IEM still there?- Sergedc
- Post #1,447
- Forum: Portable Headphone Amps
-
Balanced cable on an IEM - snake oil?
The snake oil is thinking that Balanced in itself is better. HOWEVER: if the performance of balanced output of your headphone amp is better (more power or lower noise) than the single ended output of that same amp, then yes you will benefit from going to Balanced. In the case of IEM you would...- Sergedc
- Post #45
- Forum: Sound Science
-
HRT HeadStreamer Firmware
LifeisinaBlink, Let me know if you face any issues- Sergedc
- Post #7
- Forum: Introductions, Help and Recommendations
-
Connecting on Line level output
I thought I would give an update: I bought a RCA male to 3.5mm female, and the result is the following: - In pure dac mode (pre amp off): the sound is very distorted, not usable - With the pre amp on: - the trick is to leave the preamp to minimum level and foobar volume to max. This give...- Sergedc
- Post #5
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Comment by 'Sergedc' in item 'Shure Aonic 5'
Triple flange: why torture? I guess they go in too deep in your hear? Have a look under the 3rd flange (the bugger one), you will see a plastic dot protruding. Cut off everything that is after this dot. Easy way to do that: squeeze it into a large nail cutter and cut it all off in one go...- Sergedc
- Head Gear comment
-
$500 iem vs $500 headphones?
I see this argument a lot. Why would you buy SE535 to connect to a phone or laptop.... When it comes to IEM / Headphone I see so much talk about headphone amplifier and so little about DAC. And people say, "its great, with IEM you need nothing else". In my opinion, in a iem / headphone setup...- Sergedc
- Post #79
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Connecting on Line level output
After reading I wonder if there might be an impedance problem. For these IEM seems like the recommended output impedance is less than 1 ohm. The RCA output is probably a lot more than that, no? (I found out the XLR output is 50 ohm)- Sergedc
- Post #3
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Connecting on Line level output
Hi, I have a Yulong DA8 II DAC and a pair of Shure Aonic 5 (36 ohm and 119 dB SPL/MW @1kHz sensitivity) The headphone amp is way way too loud, and produce too much noise. What would happen if I connect the IEM on the RCA out (at the back) instead (I know I need an adaptor)? Not enough power...- Sergedc
- Thread
- connection iem iem amplifier
- Replies: 4
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Radio interferences in headphone amp
I have a pair of Shure Aonic 5 (34 ohm, 119 db sensitivity) and I am trying to have a noise free experience. I have a Yulong DA8 II DAC, and using the headphone amp of the Yulong, I am getting a lot of noise / wind. This was mentioned in someone else's review (for sensitive IEM). Hence someone...- Sergedc
- Thread
- Replies: 1
- Forum: Headphone Amps (full-size)
-
HRT Headstreamer USB DAC - Updated firmware and now volume is stuck at max
For anyone still looking for these files- Sergedc
- Post #4
- Forum: Dedicated Source Components
-
HRT HeadStreamer Firmware
Here it is, actually it was on their website with broken link Be carefull, mine was not a "Headstreamer" but a "headstreamer mobile", different file. The tool will warn you if you are using a bin that is not for your device. But give you are at 1.5, you have a "Headstreamer"- Sergedc
- Post #5
- Forum: Introductions, Help and Recommendations
-
HRT HeadStreamer Firmware
Someone must have these files, maybe an ex-employee ( I have reached out to 2 of them on linked in, lets see) Or a user that saved them... I find it frustrating that when these companies go bust they don't put the files in a public place.- Sergedc
- Post #4
- Forum: Introductions, Help and Recommendations
-
Yulong DA8II In-Depth Review
@earphonia: awesome review. I have owned the DA8II for 7 years and very happy with it. For the first 6 years I used it with RCA output. Only recently I started using it as a headphone amp, but facing a problem. When I turn it on, there is some white noise (like wind) coming in the IEM (Shure...- Sergedc
- Post #25
- Forum: Dedicated Source Components
-
HRT HeadStreamer Firmware
Hi, did you manage to find anything out? Mine seems to be on firmware 1.0 (USBView says "iManufacturer: 0x01 0x0409: "www.hirestech.com 2012 Rev 1.0") Do you by any chance have the 1.5firmware file?- Sergedc
- Post #3
- Forum: Introductions, Help and Recommendations