Here's the reference document from Smyth about the TCP server: A16-IP-command-server-May-2020-1.pdf There are two tables. One is a complete set of all the buttons on the IR remote. The other table is where the value add comes in: Direct input source selection User A and User B Preset selection...

Most of what you are asking is not possible directly (only through the IR commands), and certainly not mirroring the screen. Read through the TCP Command document - only commands that are listed there are possible. Which is basically an app version of the IR remote plus better input & preset...

Just in case - make sure you disable TCP Slave in the network settings. In my testing it causes communication to become a lot slower, because it can't process a new command until it's done ACKing an existing command, or while it is transmitting its TCP Slave "heartbeat" status line (every 1...

I do not think the hardware inside the A16 is at all capable of this. The TCP server is an ASCII level text interface with about a 500ms latency per command.

Like i mentioned, only if Smyth would implement a mechanism in the TCP server that allows us to fetch a screenshot of the screen. Today this is not possible. The TCP server only supports 2-character hex commands and only returns ASCII text, so I have my doubts that it is possible at all to...

Should be possible. or some way to directly pick a volume level.

Actually during HPEQ adjustment (manloud), the TCP interface doesn't even work. That was my initial plan a year orso ago, to make that a better user experience. What I've done in the past is to set up a webcam pointed to the screen and connected to a raspberry pi with go2rtc on it. I can then...

Gentlemen, if I were to publish an app for the A16 that does basically the same as the Centro Control app, but now it's native Android (and possibly IOS too if a lot of you are iphone users) - would you use it? If yes, would you pay $9.98 for it? If not, why not or how much instead? And on...

Ever since i upgraded from 2.05 to 2.12 in December (i did a factory reset) I always have to toggle the Audio Source (e.g. hdmi1 to 2 and back) before I get picture from my shield tv on my LG oled. This was never a problem, it just always worked. I used standby bypass back then and am using it...

I agree. But that's the only explanation I have for the imbalance i had. See previous HPEQ here: https://www.head-fi.org/threads/smyth-research-realiser-a16.807459/page-849#post-16635525 Weird. Might have made an error there. My manLOUD process is basically: Select my headphones Select one of...

Actually I think it's fixed. I have explicitly disabled HT and now the imbalance isn't as strong. I still have to adjust balance for many individual subbands but this new HPEQ looks a lot more balanced to me, as opposed to a previous one where L was nearly flat and R was even worse than this

Ok, I don't see it. If you start a manLOUD and you are on Band 1, there is no way I can adjust gain separately for L and R. Only on bands 2 and up the HPA and HPB volume buttons function to adjusr L and R gain individually. Are you really sure you are able to adjust Band 1 separately? I can...

Is there any way to adjust the first bands on a manLOUD (the two yellow bars) individually for the L and R channel? I can adjust the gain but only for L+R together. Am I missing something? An unlock toggle somewhere perhaps?

I've made this PRIR just now, but what atmos room config is this? I'm having a hard time finding the correct room for this L,R,SW,C,Ls,Lw,Lb,Lss,Rss,Rb,Rw,Rs setup or how to map it to an atmos speaker preset.

I saw mentioned that a HPEQ should first be used so that the subband noise sounds centered. I've done just that on the BBC room but I'm getting quite the strange EQ result. Is this common? Is there some general L/R balance setting i should change? Or should I have my ears or headphones checked?