Recent content by Dreamslacker
-
Help fixing B22
First, remove C14 from the board until a suitable replacement can be found. It is not critical to the operation of the board. You just want to make sure that the cap doesn't swing around and short something else. The replacement for C14 should be a 1uF MKP capacitor but any 1uF film cap...- Dreamslacker
- Post #3
- Forum: DIY (Do-It-Yourself) Discussions
-
Soldering Iron Question... Solder won't stick!
Ok.. This is not the best suggestion you will find but it should work to cut through the crud if you take lots of precautions. Ammonia. Heat up the iron and dip in a small little container of ammonia. You must do this in a very well ventilated environment. I recommend using a fan...- Dreamslacker
- Post #39
- Forum: DIY (Do-It-Yourself) Discussions
-
Solid flux, how is it used?
You don't melt it! Heat activates the Rosin!!! To use, add Isopropyl Alcohol to a portion (best to cut a little out and put it in a small dish) and allow the IPA to dissolve it then use a brush to apply to the joints to be soldered.- Dreamslacker
- Post #3
- Forum: DIY (Do-It-Yourself) Discussions
-
Guide to ReCable (Dual Entry) BeyerDynamic DT (with pictures!)
Beyer Dynamics uses the marker pen mark to denote the positive connector on their drivers. Holds true for their other headphones as well.- Dreamslacker
- Post #6
- Forum: DIY (Do-It-Yourself) Discussions
-
What to use to clean front panels?
Dilute dishwashing liquid with microfibre cloth or chamois cloth will work just fine. The brand I would recommend (Mama Lemon) cannot be found over there though. That's what we use for cleaning everything from wood, rough & smooth veneers, CD's to LCD screens and works like a charm. It get...- Dreamslacker
- Post #8
- Forum: DIY (Do-It-Yourself) Discussions
-
reccommend a good stepped drill bit?
I use a Unibit that goes up to 1/2" as well as a 24mm HSS hole-saw for Neutrik D type panel mount units. Works well so far for all my work with Neutrik locking jacks, Noble pots, TKD pots, ALPS (Blue Velvet & Black Beauty), C&K/ Lorlin etc.- Dreamslacker
- Post #7
- Forum: DIY (Do-It-Yourself) Discussions
-
Article: $20 homebrew IC beats $300 IC?!?!
IMHO, the differences, if any, are similar to why headphone amplifiers that we build/ buy general improve the sound over an in-built headphones driver chip you get on a player. I think that the difference in sound has got to do with how much distortion is produced when the driving stage...- Dreamslacker
- Post #23
- Forum: DIY (Do-It-Yourself) Discussions
-
AD8397-class A?
Big OT here: Quote: Originally Posted by jcx The heat sink is a Zalman Golden Orb II, drilled and tapped for a ¼-20 ss socket head screw which protrudes from the center of the Cu slug bottom and to which the pcb carrying the TPA6120s is clamped Actually, that's a Thermaltake...- Dreamslacker
- Post #25
- Forum: DIY (Do-It-Yourself) Discussions
-
The shaft hole diameter of the knob for my PIMETA's RK27 volume control
Quote: Originally Posted by tomb There is a difference. Amb has posted before that it's enough to cause a slight wiggle if you use a knob with a set screw. He suggested purchasing knobs for 6mm shafts, but I haven't seen any of those. It might be a good reason not to clean all the...- Dreamslacker
- Post #13
- Forum: DIY (Do-It-Yourself) Discussions
-
Vishay Bulk Foils Resistors
Percy Audio has the 0.3W pieces at US$2.75 a pop.- Dreamslacker
- Post #14
- Forum: DIY (Do-It-Yourself) Discussions
-
Good solder options?
Quote: Originally Posted by Sinbios Any time a company tries to tell me that they have a "secret ingredient" that makes their product so much more wonderful than the next company's, alarm bells ring off in my head. If there really was such a wonder mixture, don't you think someone would...- Dreamslacker
- Post #38
- Forum: DIY (Do-It-Yourself) Discussions
-
CMoy: Virtual Grounds and Caps
The blue film caps are most probably Metalized Polyester caps. You can find Wima and ERO 3.3uF/ 50v caps in that size. That colour looks like Evox Rifa caps but I might be wrong.- Dreamslacker
- Post #8
- Forum: DIY (Do-It-Yourself) Discussions
-
Weller station sucks.
Quote: Originally Posted by RnB180 I want something better then the hakko 936 now that I think of it, I want to buy something that wont die on me, and I believe the last time I saw the 936 it only reached temp level equivelant to a 40 watt iron. can anyone give me some better irons...- Dreamslacker
- Post #21
- Forum: DIY (Do-It-Yourself) Discussions
-
Does blasting speakers damage them?
Quote: Originally Posted by AlanY They tested the brown note theory on MythBusters and determined that it's a myth. There's a bit of a writeup here, but it leaves out the ending (nothing happened): http://www.meyersound.com.au/brownnote.shtm Yep... But it's scientifically proven... -
Analog Devices High Performance Amplifier Kit? (56k Warning)
The AD8651 would be good for a Kwak Clock 7 if you ever need to build one..- Dreamslacker
- Post #5
- Forum: DIY (Do-It-Yourself) Discussions