Recent content by dnalekaw
-
Fostex T50RP Incremental Mods and Measurements
Around the 3.5mm connection in the left cup there's a pretty large gap that will cause a channel imbalance if it isn't sealed, could very well be the cause for the difference you're hearing since its effect becomes more apparent with the more damping you apply. Some non-drying clay preset...- dnalekaw
- Post #2,737
- Forum: Headphones (full-size)
-
MrSpeakers Alpha PRIME: Impressions and Discussion Thread
Just like Wes said the Alpha pads were the 'best' I've tried - they seem to have a pretty dense foam which helps with dynamics in the bass. ZMF oval proteins were the best 3rd party pads aside though, still not as impressive as the stock ones in the bass and the 8khz peak was exacerbated a bit.- dnalekaw
- Post #2,868
- Forum: Headphones (full-size)
-
ZMF Aeolus Impressions thread
If you have a leather hole punch and some sharp scissors you could do a bit of a handy-job to shorten the strap :) I had the same issue where it was slightly too long & I was already fine with comfort for less lengthy listening sessions but shortening it ever so slightly made for a huge...- dnalekaw
- Post #4,218
- Forum: Headphones (full-size)
-
ZMF Aeolus Impressions thread
The aeolus pads are from a different oem with a slightly different density foam and a thinner lambskin compared with the unverse lambskins, honestly though I've never felt anything as soft as the leather on the universe pads. I reckon Zach should venture into the upholstery business, a nice...- dnalekaw
- Post #4,092
- Forum: Headphones (full-size)
-
ATTICUS and EIKON, the new dynamic driver headphones from ZMF
As far as frequency response goes the different woods are supposed to be almost identical, however the density and amount of pores in the species can have subtle changes to the way sound is presented - harder woods like padauk tend to be more 'immediate' sounding and more 'focused' in comparison...- dnalekaw
- Post #8,157
- Forum: Headphones (full-size)
-
ATTICUS and EIKON, the new dynamic driver headphones from ZMF
I'm sure if you sent Zach/Bevin a message at contact@zmfheadphones.com they'd get you sorted! They're super responsive and helpful.- dnalekaw
- Post #8,150
- Forum: Headphones (full-size)
-
ATTICUS and EIKON, the new dynamic driver headphones from ZMF
Okay so my current mood is existentially pertubed. I have the new stock braided ZMF cable as well as the OFC cable and since I received the Atticus I had only used the OFC upgrade cable, until yesterday. Immediately I heard a difference and put it down to placebo but then I kept swapping and...- dnalekaw
- Post #8,148
- Forum: Headphones (full-size)
-
Fostex T50RP Incremental Mods and Measurements
Recreating the alpha dog mod is pretty easy! You'd need to get open alpha cups somehow and some wool felt for the rear driver but apart from that there's nothing special about them - just follow the guide for the open alpha online. Of course you do need a t50rp mk2 though. The alpha prime is...- dnalekaw
- Post #2,731
- Forum: Headphones (full-size)
-
MrSpeakers Alpha PRIME: Impressions and Discussion Thread
Get some double-sided tape and voila!- dnalekaw
- Post #2,862
- Forum: Headphones (full-size)
-
"Open Alpha" T50 3D printed headphone project from MrSpeakers
https://www.ebay.co.uk/itm/322518595045 These are almost identical to the headband screws for the T60rp, anything that's 3.5x19mm or similar should work.- dnalekaw
- Post #743
- Forum: Headphones (full-size)
-
"Open Alpha" T50 3D printed headphone project from MrSpeakers
Nope, the t20 / t40 / t50 / t60 all use the same driver, the only thing that's different between them is the actual cup and the baffle foams! You'd get the same result if you use any of them to make an open alpha- dnalekaw
- Post #727
- Forum: Headphones (full-size)
-
ZMF Ori (Omni) - Upcoming Semi Open Flagship
Yes you seem to be right, or at least that's what my complicated 'blow into them and see how hard it is to do so' tests indicate.- dnalekaw
- Post #2,484
- Forum: Headphones (full-size)
-
"Open Alpha" T50 3D printed headphone project from MrSpeakers
For anyone interested, here's what the inside of my Alpha Primes look like: Rear damping follows lattices of paxmate sound deadening foam, with stiff felt over the rear bass port. Both Alpha Primes I have had do not contain any wool, instead just a single cotton ball rolled out and laid...- dnalekaw
- Post #645
- Forum: Headphones (full-size)
-
"Open Alpha" T50 3D printed headphone project from MrSpeakers
They look damn good! How do they sound?- dnalekaw
- Post #626
- Forum: Headphones (full-size)
-
MrSpeakers Ether CX - $899 from Massdrop
That's very interesting, maybe try and contact Dan for more info. I can say at the very least that my CX looks identical to the one in Z's video.- dnalekaw
- Post #370
- Forum: Headphones (full-size)