Recent content by arielsivan
-
A
Home-Made IEMs
Hey. My first time working with the 38d1xj007mi/8a. Just want to make sure.. I shorten the + with the second + and the same with the -, right? And what is the method to shorten the pads, with the same wires that are used for wiring? Another thing, I measured the driver with a 1mm ID tube about...- arielsivan
- Post #15,913
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Hi everyone Im looking for a recommendation for a low-budget 3D scanner and printer that does the job.. I prefer from AliExpress.. Amazon is also possible- arielsivan
- Post #14,713
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
AMAZING Can you share with us the crossover scheme?- arielsivan
- Post #14,498
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Is this the correct scheme? If so, waht are the R1 and C1?- arielsivan
- Post #14,463
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Hi :) Im looking for a reference for @piotrus-g scary.. Thanks- arielsivan
- Post #14,452
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Looking for the suitable Zobel for LS61718. It looks like a 30 ohm peak at 800 Hz. I intend to fit it with a CI30120 as well.. I would really appreciate your help!- arielsivan
- Post #14,253
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Hi. Does anyone have experience with the LS ECGK 61718? It seems to be similar to bs6 (R.I.P)... I'm looking for a suitable zobel. I intend to build CI30120+ ECGK61718. So I would appreciate ideas for the electrical circuit for the configuration 😊- arielsivan
- Post #14,229
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
What an expert answer! :) Thank!- arielsivan
- Post #14,161
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Hi. I have a question for the experts here.. what are the main effects of the tubing diameter (OD and ID) and length on the frequency response? I think I noticed a smaller diameter decrease the high frequencies.- arielsivan
- Post #14,159
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
The thing is I have 4 units of bs6 and in all of them I get this roll off I'm using dayton imm-6. And recorder with my galaxy s7 (😅) Could it be that the problem is with the cell phone at all?- arielsivan
- Post #14,120
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
hi Did anyone else have a roll off issue at 4k with the bs6.?- arielsivan
- Post #14,117
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Hi everyone. Looking for a recommended build for live sound monitoring (as a singer)- arielsivan
- Post #13,699
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Can you describe how you used them? What combination did you make and did you use a crossover or a zoble? I'm trying to decide if I'm using them (because they have a really impressive FR) or should I go for MASM / Finale 2...- arielsivan
- Post #13,615
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Anyone have experience with the Langzhisheng store on AliExpress? I think they make a crossover themselves for the drivers .. They provide a response curves that look very good. The question is whether it can be trusted? langzhisheng Store https://a.aliexpress.com/_vBh8Bj Does anyone know...- arielsivan
- Post #13,608
- Forum: DIY (Do-It-Yourself) Discussions
-
A
Home-Made IEMs
Is't a GQ = ED+tweeter? There is a reason to go for other combination? (I'm not trying to challenge my self if not necessary.. while the build is stand for my expectations.. bass,soundstage and detail)- arielsivan
- Post #13,596
- Forum: DIY (Do-It-Yourself) Discussions