Hey. My first time working with the 38d1xj007mi/8a. Just want to make sure.. I shorten the + with the second + and the same with the -, right? And what is the method to shorten the pads, with the same wires that are used for wiring? Another thing, I measured the driver with a 1mm ID tube about...

Hi everyone Im looking for a recommendation for a low-budget 3D scanner and printer that does the job.. I prefer from AliExpress.. Amazon is also possible

AMAZING Can you share with us the crossover scheme?

Is this the correct scheme? If so, waht are the R1 and C1?

Hi :) Im looking for a reference for @piotrus-g scary.. Thanks

Looking for the suitable Zobel for LS61718. It looks like a 30 ohm peak at 800 Hz. I intend to fit it with a CI30120 as well.. I would really appreciate your help!

Hi. Does anyone have experience with the LS ECGK 61718? It seems to be similar to bs6 (R.I.P)... I'm looking for a suitable zobel. I intend to build CI30120+ ECGK61718. So I would appreciate ideas for the electrical circuit for the configuration 😊

What an expert answer! :) Thank!

Hi. I have a question for the experts here.. what are the main effects of the tubing diameter (OD and ID) and length on the frequency response? I think I noticed a smaller diameter decrease the high frequencies.

The thing is I have 4 units of bs6 and in all of them I get this roll off I'm using dayton imm-6. And recorder with my galaxy s7 (😅) Could it be that the problem is with the cell phone at all?

hi Did anyone else have a roll off issue at 4k with the bs6.?

Hi everyone. Looking for a recommended build for live sound monitoring (as a singer)

Can you describe how you used them? What combination did you make and did you use a crossover or a zoble? I'm trying to decide if I'm using them (because they have a really impressive FR) or should I go for MASM / Finale 2...

Anyone have experience with the Langzhisheng store on AliExpress? I think they make a crossover themselves for the drivers .. They provide a response curves that look very good. The question is whether it can be trusted? langzhisheng Store https://a.aliexpress.com/_vBh8Bj Does anyone know...

Is't a GQ = ED+tweeter? There is a reason to go for other combination? (I'm not trying to challenge my self if not necessary.. while the build is stand for my expectations.. bass,soundstage and detail)

Hello again. I want to start a project with the BS6. I'm interested to boost the bass .. Which driver is recommended to match them? does the MASM7 fit for that. Or would you even recommend another project? Interested in detail, soundstate and warm sound. (Used only for listening to music...

I meant, I'll take the drivers that come with the se856 (fake) headphones in the link. I make the shell, the tubing and the connectors etc ..

And it does not come tuned? There's a crossover there. And they also show a response curve that looks very good .. Are you still do not recommending? What about buying the real drivers of se535? https://a.aliexpress.com/_vUyRos I hade a bad experience with the bs6 .. I really did not like...

Hello everyone. I saw that they sell on AliExpress diy se846. I was thinking of buying them for their 16 drivers and putting them inside my CIEM. In addition, there is no need to build a crossover ... Has anyone tried them? I would love to hear your opinion https://a.aliexpress.com/_uz049S

Thank you!! Exactly what I wanted to hear :)

Will 30 grams of Dreve resin be enough to make 2 pairs?

Ok thanks a lot

Hi everyone. I want to start the BS6 project. Is there any reason why I shoden't use cheap resin from AliExpress? like this one: https://a.aliexpress.com/lFpnW75q This greatly reduces the cost of production. And another thing, should I wired the zoble directly to the built-in crossover...