Thanks for your prompt support. However , regarding to my attached picture, can you please let me know which side of the dip switch means “ON” ? The number side (left) or the opposite side (right) ?

Hi , I am a bit confuse that which side of the dip switch means “on” or “off” Please see my picture I am setting as Psaudio which should be “ON” on sw9 and sw10 and plus DSD output “ON” on sw1. Is this correct ?

Hi Gonintendo, After adjusted Su6 i2S switch with PSaudio setting , my Wandla still couldn’t read DSD file from Roon. Do you any other setting for this circumstance? Thanks in advance

How do you set up the Singxer su6 with i2S output to Wandla ? Wandla couldn’t read the DSD file at all when I use Singxer su6.

Switch to “on” at bypass setup

Already updated the new firmware 1.2.0 with two new filters HQ Apod MP and HQ short. Sound getting better with HQ Apod MP a bit , in my opinion.

Agreed , I have already checked, it’s still 1.1.1 version so far

Hi everyone, What is the latest firmware of Ferrum Wandla at the moment ? Is it the latest one version 1.1.1 ? Thanks

Thanks for your kind sharing this infomation. it means that to change the PSU (such as Hypsos instead of the stock ifi ipower) will not effect to any sound then. Because it is only supply to LEDs and Relays. Then I will use the Ferrum Hypsos to supply to another devices to get definitely...

My last setup with ifi pro IESL with ferrum Hyspos at 9 volts. However the output power is showing only 2.0 watts and 0.2 A. K, is that alright or should I go down to 7.5 volts to get more power ? IMO, the ferrum Hyspos is better than ifi ipower stock (in term of sound) My setup is using...

Can you please compare the two Zmf headphones with Ferrum Wandla ? I am looking for to buy a ZMF headphone either Atrium close, Atrium open or Verite close in the end of this year. My music genres is soul , EDM , hop-Jazz , alternative 90’ mostly. Thanks

My final position , OOR will be on top of Wandla on right side and the left side will be 2 Hypsos stack. the feet of Ferrum stack is Isoacoustic Orea Bronze model (19 mm. height)

Hi Oldnewb, In my opinion, I do prefer 26 voltage rather than 24 voltage from Hypsos to Wandla which it made Wandla got more dynamic and holographic noticeably. However , if it went to 28 volts, Wandla got more punchy and low end but the airy was decreased dramatically. So, my favorite sweet...

My Ferrum stack setup , they are using 2 units of Hypsos to supplies the different voltage to each device. The different voltage in each headphone , the upgrade sound I could get from each headphone.

Just ordered a Wandla yesterday, I already got Hypsos and OOR in my system. In fact I already got the Plixir LPS (24 V 2 Amp) which can be used with Wandla. Can I ask you more question about the alternative ways to maximize the performance (within reasonable cost) of Ferrum stack as below 1)...

It can also control my Fiio M17 , Brilliant product. 🏆

Still in love with original PRO IESL

Can I use ifi ipower elite 5 volts instead of 9volts (stock cable) ? Or use ifi ipower X (9 volts) ? Which voltages is the best match with IESL?

Thanks, can you please recommend the LPS for pro IESL instead of the stock one? Which is the best voltages for this IESL?

Using Susvara with Pro IESL and chord Ultima5 today, the results was very good with 350 watts of amp.

Thanks for sharing . What is the exact specification of material of the analog cable to get the most effectiveness? Pure silver , pure copper or silver plate copper?

@iFi audio Can you please recommend the specificaltion of the cable 4-Pin XLR equipped headphone amplier to the balance headphone amp input ? Does it need to be the digital cable (coax impedance ratings (typically 30 to 90 ohms)) or just the normal adapter cable ? Thanks in advance