Search results for query: *
- Users: blanquartc
- Order by date
-
B
Smyth Research Realiser A16
Good morning, I solved my problem by using "native" in Audio LM.- blanquartc
- Post #15,290
- Forum: High-end Audio Forum
-
B
Smyth Research Realiser A16
Thank you for the answer. Unfortunately if the Auro function is switched on and activated, whereas in the case of Auro support, this is decoded correctly. My problem is the opposite while atmos and PCVM are decoded correctly the DTS is upmixed by auromatic although I did not activate it in my...- blanquartc
- Post #15,289
- Forum: High-end Audio Forum
-
B
Smyth Research Realiser A16
Hello again everyone, I now have a problem following firwre 2.15 (possibly from understanding on my part) PCM, Atmos and Auro work perfectly (I do not want to use Auromatic and do upmix. Consequently I did not enter auromatic against my HDMI input. Unfortunately for everything that is DTS I go...- blanquartc
- Post #15,287
- Forum: High-end Audio Forum
-
B
Smyth Research Realiser A16
Thanks @Litlgi74 and @VandyMan for the help. The problem seems solved. The MAC address was correct but before seeing the message from VendyMan I had connected the A126 directly to the router without going through the hub of the network and oh miracle my ipad connected without problem. I then put...- blanquartc
- Post #15,286
- Forum: High-end Audio Forum
-
B
Smyth Research Realiser A16
Thanks @Litlgi74. I tried several IP addresses available on my network and no improvement. Are you using firmware version 2.15? Thank you so much. Christian- blanquartc
- Post #15,282
- Forum: High-end Audio Forum
-
B
Smyth Research Realiser A16
- blanquartc
- Post #15,281
- Forum: High-end Audio Forum
-
B
Smyth Research Realiser A16
Hello everyone, After a long absence due to health problems and non-use of the A16, I have just put it back into service and encountered a problem that I did not have. This is the use of CentroControl for the use of IP commands (TCP). Until the forced cessation of use everything worked without...- blanquartc
- Post #15,278
- Forum: High-end Audio Forum
-
B
Smyth Research Realiser A16
After sending my previous message, I tried again to switch from 1.60 to 1.81 and then did a factory reset, and although the presets remained the problem seems to have disappeared. I will reinstall my presets to avoid mixing and keep you posted. thanks again Christian- blanquartc
- Post #7,818
- Forum: High-end Audio Forum
-
B
Smyth Research Realiser A16
Thank you very much for helping me. Regarding messages at startup I took note. For the prtoblem of the message "HDMI!" unfortunately the reload systematically gives the same error message whatever the input chosen and the source changes. Even if I click on the message with or without signal at...- blanquartc
- Post #7,817
- Forum: High-end Audio Forum
-
B
Smyth Research Realiser A16
Thank you for your interest. The problem is here. At the moment my A16 is funcionning correctly with 1.60 firmware. I informerd Gille Guerin for the problem wih this information: Je me permets de faire le point sur le problème et l'interprétation que j'en ai. Problème : après avoir effectué...- blanquartc
- Post #7,815
- Forum: High-end Audio Forum
-
B
Smyth Research Realiser A16
Hello, Sorry for my bad english. je have an A16 from two month. I use it very basiquely with PRIR from A8. I make the upgrade of the firmware without problemto the 1.75. For the 1.81 i make the directly the upgrade from 1.75 in the same mode with the factoy reset . First surprise my preset...- blanquartc
- Post #7,789
- Forum: High-end Audio Forum