Search results for query: *
- Users: heatmizer
- Order by date
-
Tranny wiring.
For 230V operation, connect primaries in series by connecting black and re lead wires together and apply 230V across yellow and violet leads wires. For 115V operation, connect primaries in parallel by connecting yellow and red lead wires together and black and violet leads wires. To parallel...- heatmizer
- Post #3
- Forum: DIY (Do-It-Yourself) Discussions
-
Mini^3 initial check help!
What happens when you touch the 2 leads together? It should read 0 ohms. red and black oriantation won't matter for ohms testing. It will matter for voltage tests. Red positive Black negative Also check out Tangents video on how to use a multimeter: How to Use a Multimeter- heatmizer
- Post #2
- Forum: DIY (Do-It-Yourself) Discussions
-
HowTo: Build an Ultra-Slim LOD Cable
tip is left- heatmizer
- Post #29
- Forum: DIY (Do-It-Yourself) Discussions
-
Dark/Fluxy joints
pcb board dirty, corroded or varnish on he solder pads?- heatmizer
- Post #9
- Forum: DIY (Do-It-Yourself) Discussions
-
Having problems with 5G Ipod Video
Itunes can reload the firmware on the ipod- heatmizer
- Post #10
- Forum: DIY (Do-It-Yourself) Discussions
-
Millett "Starving Student" hybrid amp
That jack from jaycar. Be careful when you tighten it the plastic thread strips easily. pin 4 is left, pin 8 is right, one by itself on edge is ground- heatmizer
- Post #1,235
- Forum: DIY (Do-It-Yourself) Discussions
-
Plastic repair (stripped)
I don't think that the locktite will work. This is what you want: Loctite Consumer Retail Products | Product Detail These methods have worked for me Take thin long plastic shavings same type plastic as hole to be repaired. run the screw into the hole with the shavings. heat the head if...- heatmizer
- Post #5
- Forum: DIY (Do-It-Yourself) Discussions
-
Post pics of your builds....
My Starving Student Bud enclosure. 4.5 "x 4.5"x2.5". What a pain to polish.Was not able to all scratches out even with 1200 grit paper. Aside from the tubes and sockets everything was around the house. Heatsinks are cut down cpu heatsink. Don't know if it works, still waiting for power supply.- heatmizer
- Post #3,556
- Forum: DIY (Do-It-Yourself) Discussions
-
Millett "Starving Student" hybrid amp
Oh Its large enough. Actually Bud enclosure. 4.5 "x 4.5"x2.5". What a pain to polish.Was not able to all scratches out even with 1200 grit paper. Aside from the tubes and sockets everything was around the house. Heatsinks are cut down cpu heatsink. Don't know if it works, still waiting for...- heatmizer
- Post #975
- Forum: DIY (Do-It-Yourself) Discussions
-
Millett "Starving Student" hybrid amp
Bump, Would there be any problems with going to 1 uF film for c2,c4 sort of use what you have. thanks- heatmizer
- Post #936
- Forum: DIY (Do-It-Yourself) Discussions
-
Millett "Starving Student" hybrid amp
Would there be any problems with going to 1 uF film for c2,c4 sort of use what you have.- heatmizer
- Post #921
- Forum: DIY (Do-It-Yourself) Discussions
-
my Cmoy gots voltage probs
Reflow your solder joints. sounds like loose connection- heatmizer
- Post #3
- Forum: DIY (Do-It-Yourself) Discussions
-
Cmoy OP AMP help.
Yup. check out Tangents "Notes on Opamps"- heatmizer
- Post #6
- Forum: DIY (Do-It-Yourself) Discussions
-
Cmoy OP AMP help.
tl082 but needs more than 9 volt to operate.- heatmizer
- Post #4
- Forum: DIY (Do-It-Yourself) Discussions
-
Opamps stage design questions
Sounds like a ground loop. 1st Plug the sub into the same power strip 2nd Did you try lifting the ground on the sub?- heatmizer
- Post #19
- Forum: DIY (Do-It-Yourself) Discussions
-
LM386 questions
lm386 Is a cheap audio amp chip. Rather noisy and the gain is bit high, 20 db. Is really a tiny speaker amp but is used for headphones.- heatmizer
- Post #2
- Forum: DIY (Do-It-Yourself) Discussions
-
Ultra-low distortion sound card input for FFT?
UsbPre: Used in prosound really good unit. USBPre Microphone Interface for Computer Audio | Sound Devices, LLC- heatmizer
- Post #8
- Forum: DIY (Do-It-Yourself) Discussions
-
Calling all Adventurous DIYer's: $200 if you can build it
Did something similiar for a cellphone and ipod setup. http://www.head-fi.org/forums/f6/sou...ircuit-230855/- heatmizer
- Post #19
- Forum: DIY (Do-It-Yourself) Discussions
-
soha tubes - how much impact on sound?
Yes you must rebias.- heatmizer
- Post #15
- Forum: DIY (Do-It-Yourself) Discussions
-
soha tubes - how much impact on sound?
The RCA blacks are nice. and yes the lm337 gets hot.- heatmizer
- Post #2
- Forum: DIY (Do-It-Yourself) Discussions
-
Simple to DIY ur State of Art Grado RA1 Amplifier
Its a cmoy. Has 4,7K resistors for railsplitter instead of the middle of the battery.- heatmizer
- Post #4
- Forum: DIY (Do-It-Yourself) Discussions
-
Meier crossfeed circuit
xinfeed: I believe itgoes between source and amp.- heatmizer
- Post #9
- Forum: DIY (Do-It-Yourself) Discussions
-
What order should I work on my projects in?
Your wife give you the honey do list yet?- heatmizer
- Post #3
- Forum: DIY (Do-It-Yourself) Discussions
-
Is there a way to coil a straight cable?
Umm wrap the cable around something?- heatmizer
- Post #2
- Forum: DIY (Do-It-Yourself) Discussions