I will take your word for it. I will just go straight cable. Is ButterflyPhoto an authorized dealer? I would like to buy this because they headphone is cheaper than buying just the...

Can't decide between limited editions or regular! :/ coiled is probably better for me but I want limited editions

Looking for a Closed Headphone that looks good for outdoor/indoor use that also has a great Bass and it all round good at everything. I play games a lot and listen to mostly rock/sometimes classic. Price Required 300 USD at max.

Hey Guys I was wondering if there was any deals on the AKG K550 or possibly an E10/E11

I am aware that open backs will be bad. That is why I prefer semi-open or closed 

Hey Guys, Since I will be going to college in about a year. I want a set of headphones that are either semi open or closed back but I want the feel of a open can. I have a budget of 500 USD for an amp + headphone. My original thoughts were of getting a E17 + Hd598 but sincve E17 are not readily...

Hey Guys, Since I will be going to college in about a year. I want a set of headphones that are either semi open or closed back but I want the feel of a open can. I have a budget of 500 USD for an amp + headphone. My original thoughts were of getting a E17 + Hd598 but sincve E17 are not readily...

Hey Guys, I have been eyeing on the HD598's for a while but no deal has come up yet. So i was wondering is there anything on par with HD598 but a bit more base and it is a open can? I would like to get a E17 along with it and I am waiting for a deal on the headphones 

HD598 is not coming for 170 USD! E17 is not on amazon yet! I hate being limited to my amazon credit. Is there any good deals for HD598 at electronics expo?

Now I took it out of the case. Wiggled the wires around and it started to work and the distortion went away. But when I put it back into the case the issue occurs again. But still doesn't explain why the led is not working. 

ISSUE! So I got everything wired up and completed today. After I tested the potentiometer and I put in the input jack wiring and then I got buzzing when I plugged the source. Now before the potentiometer and output jack were tested separately and they worked. Now the LED also stopped working. I...

Thank you. I was referring to the wiper pins and the switch pins on the pot. I normally just coil the wire around the pin and then solder it. 

Okay so I decided to use electrical wire as insulator for the circuit board, however I did find this foam based stick on material in my house that was used in mounting a Air conditioner. Should I switch the insulation?  The front panel components do they need insulation as well? I am using...

Quote: I get the most out of it with my limited 300 dollar amazon credit. Someday I will move on to better products. 

I will upgrade slowly but buying 300 dollar can's is not in my budget anytime soon. I will buy something like those V-moda's. Well I am sick of listening to my bassless speakers, I assume I can get a decent punchy bass out of the amp. I know that HD598's don't have much bass but with a cmoy+e17...

Quote: Mostly Going to be gaming. Not really going to take Open Can's outside of the house. I would like to have them so I can jam to music as I study. I am going to probably keep these even when I go to college for the same reason or maybe switch to some V-Moda's. 

Quote: I have about $300 dollars worth of amazon credit. I am waiting again for the HD598 170 USD deal again. I doubt I would be upgrading for a while.     

I read through the review again. Now I am little anxious and want the Alpen E17. My setup is going to have a HD598. I am not sure if I should buy a E9+10 combo or just a E17. Both will cost about the same but which one will be better? I already have cmoy for portable use and if I get the E17...

15 dollars for those cables is expensive. I would rather just get spilter cable for 5 bucks

Where could I find a 6inch 1/4inch female to 3.5mm male cable.

I have an Amazon gift card so I would rather pay nothing get the HD598s

I wait for the 170 dollar Amazon Deal to comeback. -_- Seems like the longest wait. 

Hey Guys! So far, I have completed sodering the entire board. Now I am at the testing phase and today in my robotic's class it did not work very well. But I found out after robotic's that i had switched the input and out of the right channel. It did work for a fraction of time and also I had...

I am just using 20 ga for the jumpers. The panel wiring I am using smaller gauge wire that is more than one strand.

Is there anything like that cable that comes in a 3.5mm variance?