Can a Millet Hybrid headphone amp be used as a phone stage?

Is there any STEPS or YJPS boards out there in circulation or is there a replacement board.   I would like to build power supply that fits in the 6.3 x 4.06 x 2.09 enclosure (Mouser P/N 546-1455N1601BLK.)

Great setup for the Treads power supply.  I am looking for a solution like this to power my Millett Hybrid. I ordered the treads a couple years ago, but I am now getting back around to using it.  I do have a some question about your Treads build.   -- Is this the case you used...

Wait, it looks like the Shure 840 pads are pleather as well?

Excellent.   Which fit better? DT250 pads or Shure 840 pads? Is there a quality difference?

Anaxilus, Thank you for this feedback. It's encouraging to hear that the M50 may not be as thin sounding as the HFI-700s.   How do they compare when it comes to fit/finish and comfortability.  These two cans appear to have a very simular designs.  However, I am having a hard time getting it...

I have been looking at getting a pair of ATH-M50 to replace a pair of Ultrasone HFI-700 that I have.  Would this be a good idea?   I have not been that impressed with the Ultrasone HFI-700 since I got them a few years back, to fill the "closed can" role.    I have a pair of HD-650, which...

Quote: Originally Posted by dsavitsk Something isn't right. You should turn off any audio processing on the computer end (iTunes "preamp", equalizers, etc) and all volumes on the computer should be all the way up. On the sonica setup, turn off all of the surround sound and upsampling...

Quote: Originally Posted by Megaptera There's already a LM317 in there for the Mint. Does it matter to the 24V regulator whether a second load is added in series or parallel to the first? With a voltage regulator stepping it down to 5V, would it even count as a second load? My real...

Quote: Originally Posted by dsavitsk Try different drivers, this should boost the output (i don't remember off hand which ones are the output limiting ones, but a search might bring it up.) Note, though, that the output is a bit lower with the sonica than some other cards, especially...

I was looking for a portable UBS sound card/DAC for a laptop so I purchased a used Sonica. The Sonica has a very low output from the 1/8" jack, even when running the output through a portable cMoy. As is, the Sonica is useless for portable use, since the laptops onboard sound card has more...

Quote: Originally Posted by GuffMorgan Jaypetermen, those are some great looking amps, how're they sounding? I just finished the Millett-Hybrid this week, so unfortunately I have not listener to it much. I need to start listening to both amps more now that I am 95% complete with...

Quote: Originally Posted by Teerawit Yowza! Very nice! Did you use Front Panel Express? Also what cases are those? Thanks, I have attached a BOM for the STEPS and Millett-Hybrid. I am trying to attach a BOM for the M³, however it's 25.4 KB and the limit is 25 KB. Yes...

How would the 0.18uf/600V Solen polypropylene capacitors compare to the 0.10uF Wima MKP10 capacitors for C4L/R? I have a couple extras and they look like they could be squeezed in.

Has anyone used the 470µF/100v ELNA ROB Capacitor for C7? How does it compare to Cerafine or Muzes for this purpose?

Quote: Originally Posted by Nisbeth I have now completed two versions of the updated Millet Hybrid headphone amplifier. PCBs before they were cased up: /U. Very impressive builds. Have you had a chance to perform an A/B comparison on the two boards? With the on...

n_maher, Sorry for the confusion. I already have a sufficient quanity of Millet-Hybrid boards and I thank you for that . Let me try to rephrase my quesiton. Is the intent to add on the "group buy" Millet-Hybrid board to make it balanced or make a completely new board?

Would the balanced Millet-Hybrid require a new PCB board design or is the idea to add/modify the new Millet -Hybrid boards for the resent group buy. I would be interested in a balance Millet-Hybrid since I am currently planning on using an extra Millet-Hybrid board, for the resent group buy...

Quote: Originally Posted by Jazper Would anyone be interested in a relatively high end portable? How would this amp rank in size and quality compared to other DIY portable amps (cMoy, Meta, Pimeta)? If similar or better then the Pimeta, I would be interested in the high end DIY...

klappar, Is the output jack of the switching variety? If so, you may want to check to make sure that it's wire correctly.

The enclosure, I am thinking about using, has an internal height of 1.3". With a .25" standoff and the board thickness I have about .75" to 1" remaining. What is a good boutique caps for C7 with a low profile (.75" to 1")?