Search results for query: *
- Users: alane
- Order by date
-
Cmoy on stripboard.
Hi, I said a while ago that i would put this up here .. its not great but it will get people started. Thanks to Pat for the original diagram. Alan Ireland/Dublin- alane
- Post #12
- Forum: DIY (Do-It-Yourself) Discussions
-
cmoy volume pot question
Cheers Till I shall have a gander Alan Ireland/Dublin- alane
- Post #6
- Forum: DIY (Do-It-Yourself) Discussions
-
cmoy volume pot question
Thanks till .. yes i am using the gain of 11 setup .. i might reduce that as to be honest i will never turn it up loud enough to use that .. unless i am going to use it for some sort of torture device... i have the R5 in there .. i have to find a pot somewhere local .. i can't order just one...- alane
- Post #4
- Forum: DIY (Do-It-Yourself) Discussions
-
cmoy volume pot question
Hi all, I built my cmoy over the weekend and as far as i can tell it is working as designed... (thanks tangent ) however due to an errant mouse click on my part i got the wrong pot in my order and it was single rather than dual .. so no good ..and nobody local has one so i havent installed...- alane
- Thread
- Replies: 5
- Forum: DIY (Do-It-Yourself) Discussions
-
quick pot question
Cheers Glassman Alan Ireland/Dublin- alane
- Post #3
- Forum: DIY (Do-It-Yourself) Discussions
-
Yet another CMoy troubleshooting question
Turing, I know that you have checked all this but i had a similar problem because i had overlooked the jumpers from the two capacitors in the power section ( the ones that go to ground ) .. it would distort badly at anything aproaching a good volume and the sound was generally bad and...- alane
- Post #9
- Forum: DIY (Do-It-Yourself) Discussions
-
quick pot question
Hi, Just a quick question about pots .. i built my cmoy and it's lovely .. however my supplier does not have a dual 10k log pot he has a 22k and 47k.. what is the effect of putting in one of these .. is that just the total resistance .. or will it take less of a turn on the pot to completely...- alane
- Thread
- Replies: 3
- Forum: DIY (Do-It-Yourself) Discussions
-
book question
Yes .. that was the one .. cheers off to amazon i go .. what do you reckon it is only available used.. Cheers Shiggins Alan Dublinl/Ireland- alane
- Post #3
- Forum: DIY (Do-It-Yourself) Discussions
-
book question
Hi, I was here a couple of days ago searching for info on putting tangents cmoy layout onto stripboard..(as opposed to the protoboard that he was using) during my search i came across a recomendation from somebody on a good electronics text and now i can't find it .. ( i cant remember all the...- alane
- Thread
- Replies: 6
- Forum: DIY (Do-It-Yourself) Discussions
-
Cmoy on stripboard.
Ok .. my thanks to you guys .. but i am such a knob .. i overlooked the jumpers from the negative side of the power supply capacitors to the earth .. i have no idea what they do !! but they were obviously important as i now have un distorted stereo goodness .. i suppose following the directions...- alane
- Post #9
- Forum: DIY (Do-It-Yourself) Discussions
-
Cmoy on stripboard.
although now that i mess around a bit i hear that i am not getting stereo when the pins are bridged/connected to power.. i am getting the left channel only but in both ears .. when i move the balance to the right i get a nice little mid frequncy hum when the pins are bridged .. and on further...- alane
- Post #8
- Forum: DIY (Do-It-Yourself) Discussions
-
Cmoy on stripboard.
cheers nkd, yeah i checked the breaks under the chip with the multimeter.. they are all cool .. i am not sure if i got the leg/pin numbering right in the last post .. when i bridge pins 3 and 4 i get a strong undistorted signal .. it is not in one ear or the other the effect is across both...- alane
- Post #7
- Forum: DIY (Do-It-Yourself) Discussions
-
Cmoy on stripboard.
Thanks Rexel and NKD, I managed to decode pats layout .. ( located here http://www5.head-fi.org/forums/showt...ht=cmoy+layout ) down the bottom of the post there somewhere .. its distorting like mad and when i bridge the opamp pins 3 and 4 it goes away .. so i have to go checking... maplin...- alane
- Post #5
- Forum: DIY (Do-It-Yourself) Discussions
-
Cmoy on stripboard.
Hi all, sorry if i am going over old ground here but i had a look around and couldnt find much on this topic. I cannot find anywhere that has something similar to the protoboard that tangent uses in his cmoy layouts(i am in ireland and nothing is ever in stock ) .. has anybody done a cmoy...- alane
- Thread
- Replies: 12
- Forum: DIY (Do-It-Yourself) Discussions