Wgibson's latest activity
  • W
    Wgibson replied to the thread Home-Made IEMs.
    Yeah, you need to measure FR every time you touch it. Combine with switches if possible. But IMO anything you can adjust after...
  • W
    Wgibson replied to the thread Home-Made IEMs.
    Closest I've built was a hybrid, but go big on the 29689 tube, 1.5mm ID or bigger could work too. 1mm ID on the 38dixj, damp per...
    • 8mm dual DD BS29689n.jpg
    • 20210919_184434.jpg
    • 20210919_190955.jpg
  • W
    Wgibson replied to the thread Home-Made IEMs.
    @LegendaryDuelist sounds like you're on the right track with 29689. One or two of those with a 38d1xj should be a good starting point.
  • W
    Wgibson replied to the thread Home-Made IEMs.
    Where do you shop? Soundlink on aliexpress is one stop shop with good stuff, but if you get on taoba you can get some drivers for very...
  • W
    Wgibson reacted to Xymordos's post in the thread Home-Made IEMs with Like Like.
    Some update on what I've built recently - a 6 driver hybrid, using 4 dynamic drivers and a SWFK. Integrating the SWFK was really...
  • W
    Wgibson reacted to Aldo40's post in the thread Home-Made IEMs with Like Like.
    I did a test two days ago with a clear shell, lake3 varnish under Uv Résine:detax freeprint mould and dreve lake3...
  • W
    Wgibson replied to the thread Home-Made IEMs.
    I usually just make things work well, I don't make things look good. So I have some challenges ahead of me :)
  • W
    Wgibson reacted to Aldo40's post in the thread Home-Made IEMs with Like Like.
    Personally.I’m no problem with drève lake 3 with brush. 5 minutes to turn in UV OFF, and then I turn on the UV, I’m no bubble it’s real...
  • W
    Wgibson replied to the thread Home-Made IEMs.
    Sounds like solvent and atmospheric conditions are a secret combination for every resin, you can only gain through trial end error, so I...
  • W
    Wgibson reacted to swtnate's post in the thread Home-Made IEMs with Like Like.
    The number one cause for excessive bubbling of the coating, in my experience, is exposure to the elements. Every light in the room is...
  • W
    Wgibson replied to the thread Home-Made IEMs.
    I understand what you're saying, but due to zero experience, I don't know if this is a good thing (flash before application so they...
  • W
    Wgibson reacted to swtnate's post in the thread Home-Made IEMs with Like Like.
    Yes. The added heat gets the solvents in the lacquer to flash point super quick. Some of those solvents flash off at 75-80 degrees…...
  • W
    Wgibson replied to the thread Home-Made IEMs.
    Has anyone tried warming the lacquer slightly, to reduce viscosity and allow more even coverage? Use awarm water bath maybe? I will be...
  • W
    Wgibson replied to the thread Home-Made IEMs.
    Look closer :) imm6 in the photo. No dampers, it sounds brighter than I expected but I am also listening a little too loud, because it...
    • 20211105_092224.jpg
  • W
    Wgibson reacted to Xymordos's post in the thread Home-Made IEMs with Like Like.
    You stuffed a 13mm DD in there?! Woah Is that measurement from a 711? The treble seems to roll off super early.
Show older items
Back
Top