Featured Sponsor Listings

W

Wgibson

100+ Head-Fier From Tulsa, OK
Joined
Messages
391
Reaction score
323
Medals
0
Classifieds feedback

Latest activity Postings Classifieds listings Classifieds feedback Head Gear Reviews About

    • W
      Wgibson replied to the thread Home-Made IEMs.
      FYI, there are some knowles RDI 32216 on ebay right now. No affiliation but I got some RDI 33438 from them, haven't played with them yet.
    • W
      Wgibson reacted to crush's post in the thread Home-Made IEMs with Like Like.
      In that prototype I was utilizing the following: 28UAP01 - Grey damper E50 - Red damper EST65DA01 - Green damper No damper on the 38D2...
    • W
      Wgibson reacted to IEMbiker's post in the thread Home-Made IEMs with Like Like.
      My recent DIY CIEM. 13mm DD + Dual 26A007 + RAU. Silicon sound tube to Copper tube end. Inspired by the XJE-MH. Channel matching and...
    • W
      Wgibson replied to the thread Home-Made IEMs.
      33803 has a nice round pinna peak and decent extension with the built in crossover, 30017 is what it is. I like the 33803.
    • W
      Wgibson reacted to crush's post in the thread Home-Made IEMs with Like Like.
      Well, I was able to get the E50 more involved but I had to leave all the L-pads in. My overall sensitivity is very low at the moment...
    • W
      Wgibson replied to the thread Home-Made IEMs.
      Does anyone have comments on sharing a series resistor between drivers? For example, same series resistor to bass and also mids with a...
    • W
      Wgibson replied to the thread Home-Made IEMs.
      Aliexpress has them. Or get some hole punches and make your own. Freeze some thin double stick tape before punching, otherwise it is...
    • W
      Wgibson replied to the thread Home-Made IEMs.
      It's a good summary, but I don't even bother calculating anything until after I have individual drivers measured, and first draft of...
    • W
      Wgibson replied to the thread Home-Made IEMs.
      3% is not bad on 2nd harmonic, should just sound a little warm. Try smaller diameter tubing and/or less resistance on 38d1xj for a...
    • W
      Wgibson reacted to mattmatt's post in the thread Home-Made IEMs with Like Like.
      3d Printed clear. 👀👀
    • W
      Wgibson replied to the thread Home-Made IEMs.
      2x usound mems conamara UA-C0601-2T and one small dd:Physical tuning and Lpad with low pass caps on the dd. Too much bass but I'll...
      • 20241011_225323.jpg
      • 20241011_225045.jpg
    • W
      Wgibson replied to the thread Home-Made IEMs.
      Try taping the vents shut. With 38ap it was about -4db per single component (dual driver = 1 component) but the distortion reduction...
    • W
      Wgibson replied to the thread Home-Made IEMs.
      WBFK is 30095, or 30019 without nozzle, new automated production version is RAD-33518 P.S. Digikey has new Usound mems conamara...
    • W
      Wgibson replied to the thread Home-Made IEMs.
      Good idea. I broke the negative terminal contact not being careful enough, so was only able to test the vented 29689 connected to...
      • 7-21-24 29689 vent center tap.jpg
      • 20240721_122010.jpg
    • W
      Wgibson replied to the thread Home-Made IEMs.
      Some earhooks have thin metal wire inside the heat shrink, so it can be formed to the shape you want. It's another option that might be...
    Show older items
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
Back
Top