Recent content by Uncle Bob
-
a nod to someone who has served us well
If anyone from Sennheiser is reading this... I can't imagine there'd be any more deserving case for someone to receive a pair of HD800's - can you?- Uncle Bob
- Post #170
- Forum: Members' Lounge (General Discussion)
-
New Millett Hybrid MiniMAX (what happened to this thread?)
shame, but thanks for the quick reply.- Uncle Bob
- Post #1,104
- Forum: DIY (Do-It-Yourself) Discussions
-
New Millett Hybrid MiniMAX (what happened to this thread?)
I notice on the beezar website that only the black enclosure is listed Is this the end of the silver version or is there going to be another batch ordered?- Uncle Bob
- Post #1,102
- Forum: DIY (Do-It-Yourself) Discussions
-
a nod to someone who has served us well
I'm not entirely sure about buying Eagle, this is a bit like me buying my wife flowers... and a washing machine... As I understood it, the original intent was to show our gratitude and thank Alex for all his efforts but here we are discussing which headphone will allow him to design amps...- Uncle Bob
- Post #152
- Forum: Members' Lounge (General Discussion)
-
a nod to someone who has served us well
The headphone stand is a nice idea, perhaps a plaque could be added to commemorate the whole thing, not names per se but the community- Uncle Bob
- Post #107
- Forum: Members' Lounge (General Discussion)
-
a nod to someone who has served us well
Sorry, it's taken me while to get round to this. Have now sent a small contribution to the fund. Very happy to see Alex rewarded for his generosity and infinite patience UB- Uncle Bob
- Post #98
- Forum: Members' Lounge (General Discussion)
-
SOHA II Builders Thread
Quote: Originally Posted by Hayduke Maybe take not of which resistors you will be taking readings on and make sure there is a little extra leg on top to grab with your gripper probes. Seconded on that last point, if I were building another, I'd make sure that R6 on both channels...- Uncle Bob
- Post #618
- Forum: DIY (Do-It-Yourself) Discussions
-
OPA2132PA in the uk?
Farnell and RS Components both sell the OPA2132PA as well as a good selection of other models and makes of OPAMP. Farnell have a minimum order of £20+vat for non-account customers but it's worthwhile seeing if you can make an order of £30+vat because then it's free delivery. RS have no...- Uncle Bob
- Post #2
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Ferrari Thank you for your very kind offer. I do like the amp very much and a building a new one is a definite possibility. But I'm not going to give up on this one just yet. Besides if I do find the fault and fix it, it may give some clues as to the hiss problems reported by some IEM users.- Uncle Bob
- Post #564
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Quote: Originally Posted by Ferrari Most likely it’s a mechanical issue caused by the fall. I’m not sure if it has been asked before (I do missed posts sometimes) but… are the tubes sitting properly in the sockets? Have you tried different tubes? It's depressing because the amp...- Uncle Bob
- Post #562
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
thanks for the suggestions, I'll keep you posted.- Uncle Bob
- Post #560
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Quote: Originally Posted by Uncle Bob Did some checks on my problem SOHAII today. All voltages checked out OK but I went over all the solder joints in the left channel anyway. Still got that hiss problem in the left channel. But I've found that minor flexing of the PCB makes the hiss...- Uncle Bob
- Post #557
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Quote: Originally Posted by Uncle Bob I'm still here, and unfortunately I still have the hiss problem - I just haven't had the opportunity to sit down and work on the board. I will keep you posted on progress - I still have to make an enclosure for it. I can't consider it a finished...- Uncle Bob
- Post #551
- Forum: DIY (Do-It-Yourself) Discussions
-
SOHA II Builders Thread
Quote: Originally Posted by runeight Uncle Bob you haven't said anything lately about your hiss problem. Is it still there? And have you had a chance to measure voltages? BTW, thanks for the request to put indicators on the e12. As you know I used them on the compact hybrid. It's a...- Uncle Bob
- Post #529
- Forum: DIY (Do-It-Yourself) Discussions