Recent content by Spacehead
-
PPA v2 construction discussion
Quote: Avro, are you skilled enough to show that it is possible to etch the board at home? :)- Spacehead
- Post #1,014
- Forum: DIY (Do-It-Yourself) Discussions
-
PPA v2 construction discussion
Thanks for your help MisterX. It seems that I am so frustrated that I cannot think , when I noticed the hissing I had thought that I had finished the amp.- Spacehead
- Post #999
- Forum: DIY (Do-It-Yourself) Discussions
-
PPA v2 construction discussion
OK now I see the logic. But what about that hissing?- Spacehead
- Post #997
- Forum: DIY (Do-It-Yourself) Discussions
-
PPA v2 construction discussion
I managed finally to implement that gain switch. I used R3 2.2K + 4.3K and R4 10K , then I have switchable gain from 5.5 to 2.5. But I just cannot seem to figure out what causes constant hissing. I have it in default metal case and input grounds are tied to it. Output ground is isolated. ...- Spacehead
- Post #995
- Forum: DIY (Do-It-Yourself) Discussions
-
The GrubDAC
hmm there is a problem still... Now I have short between VDD and GND. I have managed to pinpoint it to either one of the top side ICs. I checked DAC datasheet and it should have any short related to VDD and GND because there one pin between those. But PCM2706 has. I think my PCB has damaged...- Spacehead
- Post #739
- Forum: DIY (Do-It-Yourself) Discussions
-
The GrubDAC
I think I managed to get the previously mentioned GrubDAC working. I hope it stays that way. I am relieved for now.- Spacehead
- Post #738
- Forum: DIY (Do-It-Yourself) Discussions
-
The GrubDAC
akgfan , don't worry about it. GrubDAC tests abnormally low on RMAA for some reason. Maybe it starts to oscillate or something. And, if it outputs 2V, then it would need attentuation before going to soundcard IMO Could somebody help me with my problem? The chip is possibly OK, because it...- Spacehead
- Post #730
- Forum: DIY (Do-It-Yourself) Discussions
-
The GrubDAC
I have problems with my latest GrubDAC. It gets recognized sometimes, but mostly it is an unknown device. I lifted one or two pads in the pin 31 and scratched to the first layer in 25 and 26. I just wonder, that when those are only ground connections, do I have other problems in there or should...- Spacehead
- Post #727
- Forum: DIY (Do-It-Yourself) Discussions
-
PPA v2 construction discussion
Quote: I try to implement it, thanks! I will put a strip socket in place of R4, so that changing gain is easy. I think 6k is fine but the lower gain needs to be 2k. The headphones are Denon AH-D2000, and sometimes high impedance devices.- Spacehead
- Post #992
- Forum: DIY (Do-It-Yourself) Discussions
-
PPA v2 construction discussion
Quote: I will need bass boost too so this doesn't work :) Good advice though!- Spacehead
- Post #991
- Forum: DIY (Do-It-Yourself) Discussions
-
PPA v2 construction discussion
Quote: I have hard time figuring out the correct way to use the switch. Could you draw a schematic for it? It would help a lot. I know, if there is open loop, DC offset gets very high and headphones can burn.- Spacehead
- Post #988
- Forum: DIY (Do-It-Yourself) Discussions
-
PPA v2 construction discussion
Hmm I need a switchable gain. How should I do it? I have no experience on it. I guess I will use dtdp and two R4s. But how to implement it on the PPA v2 board?- Spacehead
- Post #986
- Forum: DIY (Do-It-Yourself) Discussions
-
PPA v2 construction discussion
Hi! I have three boards which I am building. I have first bent most of the resistors to the circuit. Next I solder them. I need to build these pretty fast. Any suggestions for quick completion techniques?- Spacehead
- Post #984
- Forum: DIY (Do-It-Yourself) Discussions
-
the Pimeta-V2 thread
Now testing Ready-to-use NiMH batteries and I must say that Pimeta v2 excels so well in producing purest sound for a battery powered device!- Spacehead
- Post #309
- Forum: DIY (Do-It-Yourself) Discussions
-
my DAC design - pup1 DAC
oh people have got their boards? PM me then.- Spacehead
- Post #142
- Forum: DIY (Do-It-Yourself) Discussions