Recent content by n0de5
-
Knowledge Zenith (KZ) impressions thread
He said that he tested it but he probably stuck it into his ears for 2 seconds and pressed play on spotify and went, "Yep, this works."- n0de5
- Post #53,743
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
Yea I tried and the right side DD is dead. Oh well. I'm going to scrap the drivers that work out of the ZS6 and use the metal shell for a future project.- n0de5
- Post #53,731
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
I don't have a multimeter sadly. Do you know if this works without a Cr2032 battery? I believe they are 3.5v so I can find another voltage source if that works.- n0de5
- Post #53,729
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
I did resolder the BAs but it appears that the 10mm DD is not working. I did switch the cable's polarity and made it sound worse so I switched it back to normal. Maybe my right side was just a dud. Oh well. I'm going to take out the insides of a ZSN Pro and put them into the ZS6 shell. I'm going...- n0de5
- Post #53,722
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
The ZS6 I fixed up last night now has less bass in the broken and now fixed side. The BA drivers were the only ones that broke off though, so I don't know why the DD isn't performing as well. Does anybody know why this is happening?- n0de5
- Post #53,712
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
It either flew under most people's radar or people ignored it because it was all BA.- n0de5
- Post #53,707
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
KZ ZS10 Pros fit the bill. V-shaped frequency response and some oomph to the bass and crispy treble on the top end, but not peaky like some other KZ IEMs. If you're fine with a more flat frequency response get the BLON BL03s. The tonality is really good on the BLONs. The BLONs are 32 ohms...- n0de5
- Post #53,688
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
After listening for a bit, my ZS6's are kinda peaky in the highs, and both sides exhibit this so its not because a botched solder job (thankfully). Is this an indication that my ZS6 is a v1 because the v2's sound dark and distant?- n0de5
- Post #53,680
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
Yay i fixed it! I have a new appreciation for people who work in factories soldering small wires and stuff its really hard. The ZS6 sounds great! I also removed the memory wire that was really annoying and didn't help at all.- n0de5
- Post #53,672
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
Resoldering time. Now its just a matter of which wire to solder on. Edit: I've found that the red enamel coated copper wires are the positive or the signal in and the green and uninsulated copper wire are negative. I just have to figure out which side of the driver is positive and negative.- n0de5
- Post #53,666
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
I got these for 25. Commencing surgery right now.- n0de5
- Post #53,665
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
Thanks. Anyway is there a way to resolder the wires back on?- n0de5
- Post #53,662
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
https://www.ebay.com/usr/bcar1448?_trksid=p2047675.l2559- n0de5
- Post #53,660
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
Yup. The seller even said that he tested them and they came with the tips off though so they were secure before they were shipped.- n0de5
- Post #53,658
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Knowledge Zenith (KZ) impressions thread
so my zs6's come and I stick on a foam tip AND THE ENTIRE ****ING NOZZLE FALLS OFF- n0de5
- Post #53,656
- Forum: Portable Headphones, Earphones and In-Ear Monitors