@dhruvmeena96 @Ivan TT @kmmm @eunice thank you guys for your responses. You guys have put many things in perspective for future builds. My idea is to use the Bellsing6+Zobel for live drumming and build another one just for jamming music from my phone at the gym or wherever perhaps the Finale-2...

@kmmm Curious question, of all the projects you have done which recipe would you consider suitable for listening to music (iPod, phone, etc.) and which would you think it can work well for live playing? Also if it is possible, whichever you considered, would you be able to link the specs...

Thank you @Kulgrinda, I just want to confirm when you say "low-pass" does it mean that it Filters high freqs so low freq can pass, right? As far as the project I guess I will have to figure out how to add the acoustic foam or damper. The holes of the 3D printed acoustic structure look smaller...

@shrewdgamer This is a list that I compiled to create the IEMs from scratch. If you follow that thread there are others commenting good suggestions and alternatives for materials as well. The project is a Bellsing-6 BA driver with Zobel. There are other recipes to make your own from single...

I am very sure that the manufacturer has its own PCB-crossover board in the shell, so as you @eunice say, it may take time to tune it outside that board. My idea was to approach the project from the drivers perspective, taking them out and creating a crossover that suits my needs. I want to take...

Hello all, I have in mind another project, perhaps a Frankenstein project. I have bought This IEMs, CCA-C16 8BA drivers. I bought them from amazon but Aliexpress shows more pictures. They are OK but too bright for my taste, however, works fine for playing live. I am able to hear all the...

I have ordered the second half of this list plus the 8oz Nicefit Acrylic and the Casting ring cup from Aliepxress. The idea for the acrylic is to make my faceplate; hopefully, it will go as plan. To my surprise, the materials will be here next Tuesday, Sept 3rd. Unfortunately, the Caps and...

Would this work "Dreve Glysol 1000ml LP Cleaner Clean IEM In-ear Monitor Remove Stickiness"? Aliexpress and if this cleaner works do I still need the Polishing compound? Is hard to get Dreve, nicefit, Proc3dure in the USA which means I have to get it in Aliexpress or other sites overseas, that...

@eunice, I've got Isopropanol (Alcohol), I assume Loctite 401 is superglue and the epoxy glue is to glue the cover, am I correct? now, what is the glycerin for? is it hand lotion? @pace88, lacquer-lack3 (dreve) You mean instead of the Paraffin?

@Ivan TT, @eunice, @dhruvmeena96, and everyone else. Here is the list that I have gathered so far to build the DIY-IEM. Most of you have built these IEMs, so the list will look familiar. I have to confess that I have not searched deep on these forums for a materials list, in any case, I would...

Thank you for the reply brother @Ivan TT I get it now. It has been a minute since a mess around with electronics since I started working with software integration. I think this was the last piece to complete my shopping list. I have created a list with all the materials that I think I may need...

WOW Thank you guys @eunice and @Ivan TT. I thought I knew electronics, but you guys take the ribbon. I saw those resistors and capacitors in my research, but though they were too small, now I know those are the ones I need. As far as connecting them I am planning in connecting them in parallel...

Hi @Ivan TT I am pursuing the same project (IEMs with Bellsing 10013) and after many research and wisdom from the community, I was pointed to the same direction you took 25Ohm/22uF Zobel. Now my question is what kind of resistor and capacitors you used? When I say kind, I mean the style/model...

Hello everyone!! I am new to the site and started reading it when IEMs curiosity bit me. I am a drummer, and like many, do not have $1,000 to spend in some IEMs, so I decided to go the DIY route. To my surprise, there is a big community that not only like headphones but are down for DIY...