Recent content by Arty McGhee
-
"Open Alpha" T50 3D printed headphone project from MrSpeakers
printed a couple of these at .1 layer height they look pretty good, mounted a set using some foam tape on the edges the holes line up with the holes in the driver, sound seems a bit more open seems like a slight increase in separation and soundstage, kinda hard to tell needs more listening one...- Arty McGhee
- Post #445
- Forum: Headphones (full-size)
-
"Open Alpha" T50 3D printed headphone project from MrSpeakers
this link https://sketchfab.com/zgliszcz has downloadable .obj files for the waveguides they open just fine in cura, gonn try printing a few tonit- Arty McGhee
- Post #443
- Forum: Headphones (full-size)
-
The "Are You Serious" Thread
Grado RA1 $25.00 kit from aliexpress 3d printed case, sounds pretty good but are you serious- Arty McGhee
- Post #7
- Forum: DIY (Do-It-Yourself) Discussions
-
post your grado mods....
i've only got 3-4 hours into it so we'll see how the battery life works out from what i've read the idea of the 9-volts is quiet power no interference or buzz or hum from a cheap ac power supply, i could replace it with some rechargables, we'll see how it goes, it was mostly an experiment to...- Arty McGhee
- Post #7,761
- Forum: Headphones (full-size)
-
post your grado mods....
Thanks it sound pretty good, very neutral, plenty of power also very quiet no hum or hiss started with a circuit board and a bag of parts with no instructions so i'm happy that it works at all, went together pretty easy, the case was more work than the electronics having never heard an...- Arty McGhee
- Post #7,757
- Forum: Headphones (full-size)
-
post your grado mods....
i guess this is a grado mod this started out as an ra-1 clone board kit from aliexpress it came as a bag of parts with no instructions designed and 3-d printed a case- Arty McGhee
- Post #7,755
- Forum: Headphones (full-size)
-
"Open Alpha" T50 3D printed headphone project from MrSpeakers
dang those look nice!- Arty McGhee
- Post #408
- Forum: Headphones (full-size)
-
Hybrid Maple/Black Limba cupped V7 Build Tour Impressions
"so what" is a good one, one of my go-to's i think the M7 has a bit more on the high end than the ypsilon and some of the others, without being too harsh there's some great tube amps out there for not too much money i'm using a little dot Mk3 with mullard preamp tubes, sounds amazing- Arty McGhee
- Post #18
- Forum: Headphones (full-size)
-
FiiO X7 | DXD | DSD | 384K/64B | ESS9018+ Android | WiFi | Bluetooth | 4 AMP modules | Balanced Out |
Tidal Ver 1.15.2 no issues- Arty McGhee
- Post #17,229
- Forum: Portable Source Gear
-
"Open Alpha" T50 3D printed headphone project from MrSpeakers
male connector https://mrspeakers.com/shop/3-accessories/cable-plugs-male-for-alpha-dog-and-mad-dog-custom-cables/ wool fill https://www.amazon.com/Dimensions-Roving-Roll-Bulk-White/dp/B0099NYOAQ/ref=sr_1_15?ie=UTF8&qid=1493310186&sr=8-15&keywords=wool+roving- Arty McGhee
- Post #398
- Forum: Headphones (full-size)
-
"Open Alpha" T50 3D printed headphone project from MrSpeakers
pretty nice... can't go wrong with candy apple red its tough to get a smooth finish have you tried using wool for the stuffins, that and a piece of thin felt with a hole in the center about the size of a dime in the center is working pretty good, use the wool to adjust the bass and...- Arty McGhee
- Post #391
- Forum: Headphones (full-size)
-
"Open Alpha" T50 3D printed headphone project from MrSpeakers
i use octoprint also (its the schitt) but i slice the files first in cura on the pc then save it as gcode and upload to cura that way you get the full settings, you can upload a cura profile to octoprint but i've never been able to get it to work very well pm me and i'll send...- Arty McGhee
- Post #390
- Forum: Headphones (full-size)
-
OFC vs. OCC wire
mogami 2799 4 conductors 26 awg stranded ofc copper strip the outer and the shielding use the guts, sleeved in paracord about 20 cents a foot- Arty McGhee
- Post #49
- Forum: DIY (Do-It-Yourself) Discussions
-
"Open Alpha" T50 3D printed headphone project from MrSpeakers
i use cura you, can view by layers it should look something like this what slicer or program are you using to send to to your printer?- Arty McGhee
- Post #386
- Forum: Headphones (full-size)
-
post your grado mods....
looks good any tips on getting them out? still have't worked up the guts to do mine- Arty McGhee
- Post #7,714
- Forum: Headphones (full-size)