It really depends on the case, I had a couple of Apple cases for iPhone, and I was able to insert the plug properly, if you have a thicker case, I dint think this plug will work.
This one might work as it appears there is little extension of the plug housing. Unfortunately it's ugly, but judicious use of heat shrink might solve that issue.
Thanks for the links. I saw that style, just wish that sleeve was shined up a bit more or something. It looks cheap.
I actually just discovered the Momentum-style as well (kinda pricey though). I might go with that. I just wish Markertek had some other options, their free shipping is awesome.
I suppose I have plenty of options, I'm just being picky.
Thanks for the links. I saw that style, just wish that sleeve was shined up a bit more or something. It looks cheap.
I actually just discovered the Momentum-style as well (kinda pricey though). I might go with that. I just wish Markertek had some other options, their free shipping is awesome.
I suppose I have plenty of options, I'm just being picky.
The last one looks a little too formal to me, the black and gold one above it might work. I'm planning on sleeving the cable with some black/blue paracord. All the black ones I'm finding have "Pailiccs" on them and it looks cheesy to me.
Yea the 2 wires was my initial worry too but apparently, I read somewhere in here stated by someone that twitsting the 2 wire tight enough can have a good lasting bond and it does work!
Once made, I have not had any that spontaneously untwisted, but then my headphones have SMC connectors that screw in. Of course, I somehow made left-handed twists so when I screw in the connectors, I untwist the cable...If you have screw in connectors, make sure to make a right-hand twist. I have to over-twist, then screw in the connectors so that the cable maintains the correct configuration.
When you twist, make sure to create almost a T or a wide V shape with the two strands before twisting. Both strands should wind around each other. If one of your strands appears kind of straight, then you are not doing a proper twist.
Great point. I made my first cable because of the cable noise (that noise isn't microphonics. microphonics is something different, but is commonly used for cable noise) and the Ether C. I ended up making one cable with latex tubing for sleeving between the tips and Y (works well), and another with SummerCable SC-peacock 2 unsleeved. Both have much less noise. I'm not sure what it is with the Ether C and cable noise, but they are very susceptible to it.
I'll make this silver plated cable for the Utopia instead. For some reason it works OK with paracord sleeved cables.
The last one looks a little too formal to me, the black and gold one above it might work. I'm planning on sleeving the cable with some black/blue paracord. All the black ones I'm finding have "Pailiccs" on them and it looks cheesy to me.
If you intent to use it with paracord, make sure you check the dimension of the jack. The hole should be big enough for the cable with paracord to go through so that when completed, your cable will look more near rather than making a visible heatshrink on the outside.
Look at it, the momentum style may not be ideal in that case
Once made, I have not had any that spontaneously untwisted, but then my headphones have SMC connectors that screw in. Of course, I somehow made left-handed twists so when I screw in the connectors, I untwist the cable...If you have screw in connectors, make sure to make a right-hand twist. I have to over-twist, then screw in the connectors so that the cable maintains the correct configuration.
When you twist, make sure to create almost a T or a wide V shape with the two strands before twisting. Both strands should wind around each other. If one of your strands appears kind of straight, then you are not doing a proper twist.
I have a couple of those right angle plugs in rhodium that I can give out for free, just let me know.
Also I'll be an avid lurker here from now in case anyone needs cable advice.
Great point. I made my first cable because of the cable noise (that noise isn't microphonics. microphonics is something different, but is commonly used for cable noise) and the Ether C. I ended up making one cable with latex tubing for sleeving between the tips and Y (works well), and another with SummerCable SC-peacock 2 unsleeved. Both have much less noise. I'm not sure what it is with the Ether C and cable noise, but they are very susceptible to it.
I'll make this silver plated cable for the Utopia instead. For some reason it works OK with paracord sleeved cables.
Maybe this definition is incorrect, but this is from Wikipedia
Microphonics or microphony describes the phenomenon wherein certain components in electronicdevices transform mechanical vibrations into an undesired electrical signal (noise). The term comes from analogy with a microphone, which is intentionally designed to convert vibrations to electrical signals.
The noise you hear from rubbing a cable does not fit this definition. The noise from a tube that is ringing does.
More from Wikipedia
The term is sometimes misused to describe sounds transmitted to the ear physically by mechanical vibrations or knocks on the wires of a headphone or in-ear monitor, when no disturbance of any electrical signal occurs.[5]
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.