-
-
Iihavet0es reacted to prima186's post in the thread Schiit Freya Impressions and Tube Rolling Thread with Like.My favorite combination "6AU6" triode connection(use "6AK5 tube converter adapter"). NEC 50's 6AU6 Vacuum tube data comparison. 6SN7GTB...
-
Iihavet0es replied to the thread Schiit Freya Impressions and Tube Rolling Thread.The 220uf 450v electrolytic snap-ins have non inductive leads so switched out the the CD micas with charcrofts. I also pulled the...
-
Iihavet0es replied to the thread Schiit Freya Impressions and Tube Rolling Thread.@jlemaster1957 The guys at VnM seem to be good guys. When I ordered my 6GU7 tubes I forgot to add the 9pin adapters. They contacted...
-
Iihavet0es replied to the thread Schiit Freya Impressions and Tube Rolling Thread.https://valvesnmore.com/ There's a YT channel also, Tube Lab. It's the guys from ValvesNMore. Very informative with descriptions of...
-
Iihavet0es reacted to PoMarantz's post in the thread Schiit Freya Impressions and Tube Rolling Thread with Like.For my tastes..(all gain side) I arrived at NOS GTBs....Just Tried RCA GTBs, found them too bright on the top end "for me" ...I also...
-
Iihavet0es replied to the thread Schiit Freya Impressions and Tube Rolling Thread.Audio is expensive and I hope your tubes sell! Also if the firmware yields "better" sound try it out. Can you revert to a previous...
-
Iihavet0es replied to the thread Schiit Freya Impressions and Tube Rolling Thread.Post 3238 describes my setup. Primarily I use my PC USB as source through a holo audio titanis isolator (power is blocked off signal...
-
Iihavet0es replied to the thread Schiit Freya Impressions and Tube Rolling Thread.I'm glad you were able to fix the lifted trace and pad. Nice jumper job. Wick can be used to remove the intial amount of solder. Move...
-
Iihavet0es reacted to PoMarantz's post in the thread Schiit Freya Impressions and Tube Rolling Thread with Like.OH…..so THAT is why they have different temperature/watt soldering irons and variable irons! 🤷🏻♂️ I did not know that….i cant believe...
-
Iihavet0es replied to the thread Schiit Freya Impressions and Tube Rolling Thread.Try to work with a high temp when desoldering. The heat stays localized and you don't have to stay on the components as long. Here's...
-
Iihavet0es reacted to PoMarantz's post in the thread Schiit Freya Impressions and Tube Rolling Thread with Like.Yeah…I “thought” I could solder…but I had never dealt with printed circuit boards before. I had the biggest issue removing the old...
-
Iihavet0es replied to the thread Schiit Freya Impressions and Tube Rolling Thread.I agree with all your thoughts on the project and engagement. Also your posts and the other's are very helpful with modding the Freya...
-
Iihavet0es replied to the thread Schiit Freya Impressions and Tube Rolling Thread.I just finished installing two 2.2uf Jantzens(red and silver) per channel since I had them onhand. They're quite large so I had to get...
-
Iihavet0es replied to the thread Schiit Freya Impressions and Tube Rolling Thread.I just pulled the two wima caps from my Freya. They pass through the relays and must be tied to the different buffer stages. I'll post...
-
Iihavet0es replied to the thread Schiit Freya Impressions and Tube Rolling Thread.Hi all. Has anyone tried using a single 500v+ cap for the output coupling film caps? I think the two 250v caps are in series to get to...
-
-
Loading…
-
Loading…
-
Loading…
-
Loading…
-
Loading…