[Hawaiibadboy]

  how are you guys attaching these to your cellphones? Velcro?

 
 
 
Separate cover dressed
 

 
 
Put on
 

 
 
 
 
Very strong very clean
 

 

[x RELIC x]

Waaaaay back, early in the thread it was determined that 3G and LTE showed little to no EMI noise, but 2G/Edge cellular reception was very noisy. I heard no noise until I switched to 2G/Edge and it was brutally obvious. That's another factor besides cables acting as antennae.

 

[jarnopp]

I'm using my iPhone 6S to drive my Mojo and it's got wi-fi and phone enabled.  I'm connecting them using the supplied Chord cable and the Apple CCK (which is by the way now the Camera Adaptor -- the Apple Store no longer recognizes a search for CCK or Camera Connection Kit).  There is no noise, no hiss, no pops, no clicks, nothing but the totally black void.  

Some phones must be noisier than others and some wires must be better atennas than others.

I have the iPhone 6S and have been using "CCK" and supplied USB/micro cable. Sometimes I get interference noise. Not sure if it's when on LTE or 4G only, etc. but, when I hear it and look at the phone, I'm usually getting an email or other notification. I have gone the opposite of many here and use a 3- or 6-foot USB cable with the CCK and keep the phone further from the Mojo. Seems to have cleared it up. Also makes it easier to use the phone for selecting songs and such.

 

[oliverpool]

  Chord Mojo FAQ
 
Bookmark this.

 
Perhaps you can add that there are 2 levels of brightness indicators. You can change between low and high by pressing both + and - volume buttons at the same time to switch between them.

 

[AudioBear]

RFI and antennas border on black magic.  Sometimes just twisting a cable can pickup interference.   

 

[ipccheng]

Hi,
 
I have got my Mojo yesterday, and have charged it for overnight. I have played it for a couple of hours this morning. When I charged it again (I have turned it off), all the balls flashed once but the charging light was off. I have tried it on different chargers, 1A or 2.4A. Is it normal?
 
Rgds

 

[omastic]

  Hi,
 
I have got my Mojo yesterday, and have charged it for overnight. I have played it for a couple of hours this morning. When I charged it again (I have turned it off), all the balls flashed once but the charging light was off. I have tried it on different chargers, 1A or 2.4A. Is it normal?
 
Rgds

The lights flashing once upon connecting the charger is normal. The charging LED lights up only after a few seconds. 

 

[Ike1985]

I hear it also comes down to file format as far as noise goes,

What is the most complete, lossless possible file format, what is the Topnotch file format, and how does t one obtain it, I can get flac but I can't find DSD anywhere, I never listened to DSD if that's the best, I want the best from mojo

I've heard all the greats in the highest quality DSD possible with the TOTL ciems and mojo and I can tell you with certainty, 24/192 is just as good as DSD from mojo. I actually find myself preferring 16/44 cd rips as they are more silent without the clicks and pops of 24/192 vinyl rips.

 

[Ike1985]

I use 24/96 FLACs and find them quite good.  I'm playing 64 Ears A12s, Oppo PM-3s, and HiFiMan HEXs. None make hiss or noise.  Mojo drives phones quite well.

Also reppin the A12's and grinning from ear to ear at times while using them with mojo.

 

[jonnymooshoo]

Wow can't believe you would risk damaging the mojo with superglue, epoxy resin is much safer

Well I was originally planning on some 1/8" wood screws so this seems like a better idea

 

[SearchOfSub]

That doesnt appear to be ferrite shielded at all, my iPhone 5 causes terrible RF noise, must use airplane mode or a bunch of detachable ferrite devices with my USB. That's why I want cable with ferrite shielding from end to end.

After reading Robs recommendations of ferrite cables I was curious and digged through all my cables while organizing and lucky enough had one lying around. It was a displayport ferrite shielded (end to end) and it made a difference in lag time as well as producing clearer and better picture on my monitor (colors pop more as well as uniformity). It sure as hell did make an improvement on my monitor/video lol.

 

[Skyyyeman]

  I'm using my iPhone 6S to drive my Mojo and it's got wi-fi and phone enabled.  I'm connecting them using the supplied Chord cable and the Apple CCK (which is by the way now the Camera Adaptor -- the Apple Store no longer recognizes a search for CCK or Camera Connection Kit).  There is no noise, no hiss, no pops, no clicks, nothing but the totally black void.  
 
Some phones must be noisier than others and some wires must be better atennas than others.

My experience also using my iPhone 6S

 

[jmills8]

The Mojo with JH13pro (w/custom copper cable from plusSound which really emphasizes the mid bass) sounds overly warm, lush and mid bass heavy. In part I blame the cable. 
The Mojo with HD800 w/stock cable with anax mod sounds thin and bright (at least compared to Liquid Carbon and Audio gd dac 19). Was not expecting this. 
The Mojo with Grado GH1 (which is really warm by Grado standards) I also found thin and bright compared to Lyr 2 with Bimby). Was not expecting this also. 

Will try the Mojo with my B&K amp and B&W 705 speaker stereo system.

Try Mojo with a warmer sounding amp.

 

[nmatheis]

If they want to use a phone without airplane mode you absolutely need it, without it mojo sounds like a 56k modem trying to connect continuously.

Tried with various IEM, and no problems with my iPhone 5S as of yet even with streaming.

 

[x RELIC x]

Tried with various IEM, and no problems with my iPhone 5S as of yet even with streaming.

Change your cellular settings to 2G, let me know what you hear. :wink_face: