Head-Fi.org › Forums › Misc.-Category Forums › DIY (Do-It-Yourself) Discussions › Does anyone have the iPhone LOD pinout?
New Posts  All Forums:Forum Nav:

Does anyone have the iPhone LOD pinout? - Page 11

post #151 of 246
2/14/09 at 1:05pm
it does, but you have to build one yourself, or buy one from a store.

iPod/iPhone Dock Connector ordering
is a good place to find DIY stuff.

Qcables sell ready made ones.
Reply
post #152 of 246
2/14/09 at 1:25pm
Ok I just purchased 2 types of resistors:

1.2kΩ, 0.6W, 6.2 mm, and a
68kΩ, 0.4W, 3.6 mm resistor.

They were like only 8 cents each!

Which one works better, the 1.2kΩ or 68kΩ version?
Reply
post #153 of 246
2/14/09 at 2:34pm
Well, the 68k one and the pins pointed in on the last page is reported to work for the 3g, and most probably the touch 2g too.

The ~1K works perfectly on the touch 2g with the pins in the illustrations I posted, but I haven't tested them on the iphone 3g. I think the search continued for the 3g after the touch 2g was figured out, so I guess there were still issues. what issues? I didn't follow. if anyone can attest to the 68k working on a 2g too, I'd go with that for universality. if you don't care bout an iphone, the 1k will work. I suggest that whatever you do, don't glue that dock closed before it works!
Reply
post #154 of 246
2/17/09 at 1:25am
The 1K will work with everything, however it will result in a "not compatible" message on the iPhone 3G.

The 68k will work for everything including the 3G with no message. I've tested both on a 3G and can confirm this (however, I'm not so sure about the Touch 2G).
Reply
post #155 of 246
2/22/09 at 6:56pm
I recently purchased the Audeo PFEs which have the built in mic/control function and was wondering if there's any way to implement that functionality using the dock connector for iPhone 3G. My goal would be to build a dock connector with a USB charge cable out and a headphone out connector (4 conductor) which could provide the line out as well as the mic/control accessibility. Looking at the pinout.ru diagram it looks like all of the controls are done on the serial port but the Ridax site offers a dock connector with a pigtail which supposedly does what I'm trying to do (minus the USB).

Any ideas? My plan is to modify my external amp to pass through the mic connector so that I can still control everything with my IEMs.
Reply
post #156 of 246
2/22/09 at 6:57pm
Double Post Deleted
Reply
post #157 of 246
2/25/09 at 9:34pm
Quote:
Originally Posted by Juaquin View Post
The 1K will work with everything, however it will result in a "not compatible" message on the iPhone 3G.

The 68k will work for everything including the 3G with no message. I've tested both on a 3G and can confirm this (however, I'm not so sure about the Touch 2G).
I tried my 1k version on my 2G touch, perfect, on the iPhone 3G it was rough and staticky sound. And echoey. Really bad. Is this the resistor or something else? Going to try a 68k anyway.... Strangely the plug (from Qables) was smooth and tight on my Touch but stiff on the iPhone.
Reply
post #158 of 246
2/26/09 at 1:40am
The resistor is nowhere near the audio signal (at least, it shouldn't be). I have a 1k resistor LOD that I made and have no problems with it (other than the "not compatible" message popping up). I can't say why it sounded bad on your phone - it should work exactly the same on both devices. Did you turn on the Airplane Mode on the phone so that there would be no EM interference?
Reply
post #159 of 246
3/1/09 at 3:33pm

Anyone selling these yet?

Is anyone in the DIY community building / selling LODs incorporating this research? I have several LODs which work with my older iPods. I would like to be able to use iPhone 3G with pocket amp, without annoying messages.

I can do this with the Apple iPhone dock, but it is a bit cumbersome in the pocket.

Ideally, I would like to see a LOD incorporating the new micro-USB jack for charging while playing.
Reply
post #160 of 246
3/2/09 at 11:45pm
Quote:
Originally Posted by ruZZ.il View Post
The latest for that is to have (11 and 15)--|66k|--(21). This probably works for the 2g too, and may be more universal. maybe someone else can comment on that.
I've just finished this and tested this on the iPhone 3G, iPod Touch 2G, iPod Nano and 3rd Gen iPod. Works flawlessly on all. No messages on iPhone or iPod Touch. I used a single 68kohm resistor just to make it easy.

I think everyone can now consider this the universal solution, thank you all for your advice/input.

PS joining pin 11 and 15 can simply be done by bending the pin legs. Easier than soldering an extra jumper wire. Also, my question (re echo) a few posts up was answered by the fact that after re-inerting pins 2-4 after soldering, they had come out slightly just before gluing. I recommend not pulling them out, just soldering whilst they're in.
LL
LL
LL
Reply
post #161 of 246
3/3/09 at 11:40am
Slightly offtopic - i'm interested in getting line out on my iphone (1st gen), and when I've saved up my couple of dollars, I will order a ridax connector.

However, I would also like to get line-in to work. Has anyone had success with that? I'm wondering if the method described in this thread will allow line in to work without any other modification?
Reply
post #162 of 246
3/4/09 at 2:31am
For line-in just use the headphone jack wired to a mic or whatever input you want (female 3.5mm, whatever). Someplace (I forget where) sells the 4-ring plugs that you'd need.
Reply
post #163 of 246
3/9/09 at 6:38am
The only issue with that is that the mic input is mono, whereas the line-in is stereo (and possibly better quality?).

But of course, I can live with it, it was just if it was easy to do, the line-in is preferable - plus it opens up a whole possibility of recording from vinyl, or mixing desks straight to the iphone, for example.
Reply
post #164 of 246
3/9/09 at 1:29pm
Quote:
Originally Posted by Juaquin View Post
The 68k will work for everything including the 3G with no message. I've tested both on a 3G and can confirm this (however, I'm not so sure about the Touch 2G).
I've still not been able to get this to work without the warning on a 1st Gen iPhone. Can you confirm on the 1st Gen? It does line out, but gives me the warning. I've made several, if you can confirm that it works, then there's a revision issue or something else different between them.
Reply
post #165 of 246
3/9/09 at 4:31pm
Quote:
Originally Posted by Good Times View Post
I've just finished this and tested this on the iPhone 3G, iPod Touch 2G, iPod Nano and 3rd Gen iPod. Works flawlessly on all. No messages on iPhone or iPod Touch. I used a single 68kohm resistor just to make it easy.

I think everyone can now consider this the universal solution, thank you all for your advice/input.

PS joining pin 11 and 15 can simply be done by bending the pin legs. Easier than soldering an extra jumper wire. Also, my question (re echo) a few posts up was answered by the fact that after re-inerting pins 2-4 after soldering, they had come out slightly just before gluing. I recommend not pulling them out, just soldering whilst they're in.
I suggest you lose the ground wire near the audio pins and solder your ground to pins 11/15. It frees up the wiring near the audio pins, plus it makes for a more solid connection. Not the worse thing in the world, but it's more mechanically reliable that way.

Quote:
Originally Posted by Hase View Post
I've still not been able to get this to work without the warning on a 1st Gen iPhone. Can you confirm on the 1st Gen? It does line out, but gives me the warning. I've made several, if you can confirm that it works, then there's a revision issue or something else different between them.
68K works on my iPhone 2G 16GB. I'm not sure if you mean 1G or 2G because the 1G came in 4GB and 8GB while the 2G came in 8GB and 16GB.
Reply
New Posts  All Forums:Forum Nav:
  Return Home
Head-Fi.org › Forums › Misc.-Category Forums › DIY (Do-It-Yourself) Discussions › Does anyone have the iPhone LOD pinout?