Recent content by omgflyingbanana
-
Home-Made IEMs
Anyone know how to solder the armatures on this crossover? Should I put solder on one side, position the armature on the other side and then just melt the solder?- omgflyingbanana
- Post #6,123
- Forum: DIY (Do-It-Yourself) Discussions
-
Chinese / Asian Brand IEM Info Thread
Can anyone recommend some nice MMCX cables from Ali/etc?- omgflyingbanana
- Post #6,003
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Home-Made IEMs
Anyone know the values of the damper and resistor in the Knowles HE? Does an ED-29689 + CI-22955 with a 10 ohm resistor and 2 x 2.2uf capacitors sound alright?- omgflyingbanana
- Post #5,949
- Forum: DIY (Do-It-Yourself) Discussions
-
Home-Made IEMs
Thank you. Stupid question but could you make a mold and the actual CIEM from the same silicone? And can you use nail polish to coat?- omgflyingbanana
- Post #5,897
- Forum: DIY (Do-It-Yourself) Discussions
-
Introducing SERA by Vibro Labs
Awesome!! If possible, can you upload one of the livestreams to YouTube so I can watch it later if I can't make it?- omgflyingbanana
- Post #72
- Forum: Sponsor Announcements and Deals
-
Home-Made IEMs
Anyone know how I can make a simple full-silicone CIEM with a non-removable cable like the CustomArt Music One? What silicone and mold material would I use? What would the process for silicone shells be like? I sent Piotrus a PM but he can't reveal the specific manufacturing process, which is...- omgflyingbanana
- Post #5,889
- Forum: DIY (Do-It-Yourself) Discussions
-
GIVEAWAY — MAYA by Vibro Labs
Red all the way! Also, Luke -- I want to thank you for being so close to the community. I am still so grateful of the time where you shipped me earphone parts to build IEMs when I was in high school because I was too poor to afford them. /r/DIEMS appreciates you!- omgflyingbanana
- Post #53
- Forum: Sponsor Announcements and Deals
-
Home-Made IEMs
Using some sort of foam from ear plugs, putting a hole through them and epoxying the foam to the nozzle of the armature to the shell seems to work great. Be sure to trim the foam so it's a few mm thick.- omgflyingbanana
- Post #5,885
- Forum: DIY (Do-It-Yourself) Discussions
-
Home-Made IEMs
Hey guys, check out my ER4 clone for $43! Album Parts List: Litz wire x10: ¥3 Shell: ¥39.90 Putty: ¥17.50 (note: you could buy this from Amazon for ~$1 more) Dampers x2: ¥14 ED-29689 BA x2: ¥56 MMCX female connector x2: ¥11 (note: this is kind of pricey, relatively speaking. You...- omgflyingbanana
- Post #5,525
- Forum: DIY (Do-It-Yourself) Discussions
-
If you still love Etymotic ER4, this is the thread for you...
Hello, does anyone know the value of the two resistors in the Y split of the er4p's? Is it 25 ohm each or 18 ohm each? Trying to diy a new cable after I broke my current one haha.- omgflyingbanana
- Post #9,661
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Home-Made IEMs
Bump? Also does anyone know the value of each resistor in the ER4P? Two 25 ohm resistors?- omgflyingbanana
- Post #5,460
- Forum: DIY (Do-It-Yourself) Discussions
-
Home-Made IEMs
Hey, does anyone know how the resistor in the Etymotic ER4P-T affects the sound? Would removing the resistor add more bass to the sound? I'm only guessing this since the adapter that converts the ER4P to the ER4S adds a 75 ohm resistor to each channel and the S has less bass than the P. ...- omgflyingbanana
- Post #5,441
- Forum: DIY (Do-It-Yourself) Discussions
-
Home-Made IEMs
Damn, that's actually quite inexpensive. You pretty much have everything you need. If I'm reading correctly the only thing they don't have is the impression material?- omgflyingbanana
- Post #5,419
- Forum: DIY (Do-It-Yourself) Discussions
-
Home-Made IEMs
I apologize for the spam, but I just wanna dump some taobao links. Incredibly cheap ED-29689? (around $5.06) Shure shell Shure shell with metal tip (I think SE846 shell) Shure shell with screws Acoustic foam? Looking for more UIEM shells? I stumbled upon this while looking up...- omgflyingbanana
- Post #5,415
- Forum: DIY (Do-It-Yourself) Discussions