Recent content by jhao19
-
O2 AMP + ODAC
Haha, yeah, the O2 is only there for convenience sake, as my headphones are connected to a signal mux. So what's actually going on is this. ...- jhao19
- Post #1,981
- Forum: Headphone Amps (full-size)
-
O2 AMP + ODAC
No ODAC, just the O2. I don't own an ODAC. And cool, maybe I just don't have a trained enough ear to pick up all the doubly amplified noise or something? I just wanted to make sure all my components were safe :)- jhao19
- Post #1,978
- Forum: Headphone Amps (full-size)
-
O2 AMP + ODAC
It's mostly for simplicity reasons, as I have a port switcher attached to the output of the O2, and this way I can easily switch between headphones and speakers. As long as I don't turn on the gain setting for my O2, I don't think I hear any clipping. Will my speakers be safe as long as I...- jhao19
- Post #1,974
- Forum: Headphone Amps (full-size)
-
O2 AMP + ODAC
Would it be bad to have the audio go from Xonar DX -> O2 -> Speakers?- jhao19
- Post #1,970
- Forum: Headphone Amps (full-size)
-
O2 AMP + ODAC
I actually have a Xonar DX to act as my DAC in my computer :)- jhao19
- Post #1,969
- Forum: Headphone Amps (full-size)
-
O2 AMP + ODAC
I was just wondering if the O2 would be able to drive desktop speakers? The Klipsch 2.1 ProMedia to be exact. I'm guessing yes, as the speakers themselves are also self powered, right?- jhao19
- Post #1,967
- Forum: Headphone Amps (full-size)
-
DIY Cable Questions and Comments Thread
But I've even tried connecting everything to only 4 separate wires, and made sure there were no shorts there. Could it somehow be the plug? It can't be the headphone connectors, as those are connected in no way except to the respective side's + and - wires.- jhao19
- Post #1,326
- Forum: DIY (Do-It-Yourself) Discussions
-
DIY Cable Questions and Comments Thread
It's actually happening in my earbuds in the cables I made right now =\- jhao19
- Post #1,322
- Forum: DIY (Do-It-Yourself) Discussions
-
DIY Cable Questions and Comments Thread
Hmm, true. Then how should I stop the audio from leaking from one driver into the other?- jhao19
- Post #1,320
- Forum: DIY (Do-It-Yourself) Discussions
-
DIY Cable Questions and Comments Thread
Hi, I recently made my own cable. However, after finishing and testing it, I found that due to both ground cables being attached to the same ground pin in the 3.5mm jack, it transfers a bit of each channel into the other (only about 20% volume). I figured I could attach some diodes to the ground...- jhao19
- Post #1,318
- Forum: DIY (Do-It-Yourself) Discussions
-
Question about DIY cable for Sennheiser IE80
Hi, I recently made my own cable. However, after finishing and testing it, I found that due to both ground cables being attached to the same ground pin in the 3.5mm jack, it transfers a bit of each channel into the other (only about 20% volume). I figured I could attach some diodes to the ground...- jhao19
- Thread
- Replies: 1
- Forum: DIY (Do-It-Yourself) Discussions
-
Walkthrough for building an Objective 2 (O2)
As stated in the title, I was just wondering if there was a step by step guide or walkthrough to building the O2 amp? I already have all the parts necessary I think, but I just wanted to watch someone else do it before I go for it. -Jon- jhao19
- Thread
- Replies: 0
- Forum: DIY (Do-It-Yourself) Discussions
-
Sennheiser IE80's Impressions Thread
Hi guys, I was just wondering, do these IEM's need an amp?- jhao19
- Post #5,172
- Forum: Portable Headphones, Earphones and In-Ear Monitors
-
Question about soldering iron
Hi, after reading the DIY forums for a while, I've kept hearing the Hakko 936 is a good soldering station, but I can't seem to find it on amazon. Instead, I find the aoyue 936. Is this just as good? Is there a better soldering station out there that I should consider?- jhao19
- Thread
- Replies: 8
- Forum: DIY (Do-It-Yourself) Discussions
-
DIY Cable Questions and Comments Thread
I'm kind of in the same boat as you, and have been looking at BTG audio and Double Helix Cables. DHC is a bit more expensive, though- jhao19
- Post #1,154
- Forum: DIY (Do-It-Yourself) Discussions