[Sulbh]

Can someone compare it to benjie s5?

 

[yangian]

Will Flac file stutter when play from SD card ? My Old Newsmy G1 have that issue.

Definitely not.

 

[nesty]

Hey, has anyone been able to mod the Walnut when using it as an amp? It is sooooo loud. Is there a way to lower its initial volume. I tried the Z1 into Walnut combo and nearly blew my head up.

Have you tried the other way around, I mean source would be walnut into z1 then z1 is the audio headphone ? Thanks

 

[macky112]

Have you tried the other way around, I mean source would be walnut into z1 then z1 is the audio headphone ? Thanks

It has been mentioned a few times over at the z1 thread that z1 sounds better than v2 when both in stock form. That said if you have both z1 and V2, I don't think it makes much sense to use V2 as dap into z1 amp

Just use z1 as dap

 

[Dark Helmet]

Ppl, my 'nut is kinda broken...

It's the headphone jack, if I stick the connector all the way in, left channel is dead, but if I then pull the connector out slightly, sound seems ok, maybe left channel is still softer, could be placebo tho

Is there an easy fix? Or I need to replace the jack?

One of the resistors towards the edge of the board for the headphone out is bad. I had this happen to me and had it replaced and it works fine now.

 

[Dark Helmet]

Just got my Nut!!! It's the old ver V2 with the hold switch. Yet to try though ... charging it first.
Will changing just the Opamp makes a big diff? Any suggestion? Love vocals, opera, R&B and Korean OST ...

Looking at either the Philips NE5532AN or the the AD825AR

Thanks

Both are good the 825 will be a bit fatter and warmer. The NE5532AN I think for this application sounds better.

 

[silverfishla]

It has been mentioned a few times over at the z1 thread that z1 sounds better than v2 when both in stock form. That said if you have both z1 and V2, I don't think it makes much sense to use V2 as dap into z1 amp

Just use z1 as dap

I actually meant, just V2 as amp, since it is so loud. Any source that isn't variable just blows the ears away through the V2 as amp, making that function a bit unusable.

 

[macky112]

I actually meant, just V2 as amp, since it is so loud. Any source that isn't variable just blows the ears away through the V2 as amp, making that function a bit unusable.

Not sure about hardware change, but a software solution is to apply negative pregain to your sings in foobar2000

I mean, if you have a 'nut, you are already converting sings anyway, might as well make another batch conversion for negative pregain

 

[macky112]

One of the resistors towards the edge of the board for the headphone out is bad. I had this happen to me and had it replaced and it works fine now.

When looking for those s bad resistor Is a bad resistor acting like a short circuit or an open circuit?

 

[macky112]

I noticed official Walnut taobao listing updated his product page

https://m.intl.taobao.com/detail/de...&spm=a312a.7700824.w4004-15832814554.3.RfsAtQ

And USB DAC function was not mentioned anywhere on the page...

I thought V2.2 and V2s have USB DAC right? Otherwise another reason to go for the z1

 

[Dark Helmet]

When looking for those s bad resistor Is a bad resistor acting like a short circuit or an open circuit?

It should be open, as in you wont be able to get a reading.

 

[SabaDen]

Both are good the 825 will be a bit fatter and warmer. The NE5532AN I think for this application sounds better.

Thanks DH ... any other recommendation? Any fav? Thanks again ...

 

[minnyB]

I noticed official Walnut taobao listing updated his product page

https://m.intl.taobao.com/detail/de...&spm=a312a.7700824.w4004-15832814554.3.RfsAtQ

And USB DAC function was not mentioned anywhere on the page...

I thought V2.2 and V2s have USB DAC right? Otherwise another reason to go for the z1

Walnut V2s has USB soundcard function. Turn on Walnut V2S first. Connect Walnut V2S with USB cable to your PC/mobile. You can adjust volume level on your Walnut V2S.
If connecting to PC, don't forget to disable your PC's sound card.

 

[geo626]

Anybody has a contact or email of the makers of walnut?

 

[ozkan]

I noticed official Walnut taobao listing updated his product page

https://m.intl.taobao.com/detail/de...&spm=a312a.7700824.w4004-15832814554.3.RfsAtQ

And USB DAC function was not mentioned anywhere on the page...

I thought V2.2 and V2s have USB DAC right? Otherwise another reason to go for the z1

I couldn't make my V2. 2 work as USB DAC on my Android phone and pc.