[Joshatdot]

I have a design for a Kicker 12" sub, and I have its box dimensions, and I am looking for a app to layout cutting guide for 4' x 8' sheets (1.2m x 2.4m)

 

[Joshatdot]

NM, I just loaded Illustrator and did my layout there.

Dang .. I am going to need 1 1/2 sheets of 18mm MDF to make this box!

 

[Joshatdot]

Code:

[left]Driver : Kicker Comp VR 12 Vas : 92.8 Qts : 0.56 Fs : 26.80 SPL : 86.40 -- Project by : Josh Robinson Project for : you -- Number of drivers : 1 Box type : Vented Box size : 275.6 l Tuning frequency : 19.33 Hz Vent : 2 vent(s) 0.393 m length for each 0.102 m round Box : 18mm Thick MDF 0.696m Wide 1.091m Height 0.432m Deep 275.6 Cubic Liters Relative Freq Gain SPL [Hz] [dB] [dB] 20.00 0.10 86.50 25.00 0.01 86.41 30.00 0.04 86.44 35.00 0.16 86.56 40.00 0.25 86.65 45.00 0.29 86.69 50.00 0.29 86.69 55.00 0.29 86.69 60.00 0.27 86.67 65.00 0.25 86.65 70.00 0.23 86.63 75.00 0.21 86.61 80.00 0.19 86.59 85.00 0.18 86.58 90.00 0.16 86.56 95.00 0.15 86.55 100.00 0.14 86.54[/left]

 

[Kees]

Off topic, but how did you do the trick with the scroll window in your post?

 

[Lil' Knight]

Quote:

Originally Posted by Kees /img/forum/go_quote.gif Off topic, but how did you do the trick with the scroll window in your post?

Just put them in the

 tag [img]http://www.head-fi.org/forums/images/smilies/smily_headphones1.gif[/img]

 

[Kees]

Quote:

Originally Posted by Lil' Knight /img/forum/go_quote.gif Just put them in the tag [img]http://www.head-fi.org/forums/images/smilies/smily_headphones1.gif[/img][/i] [/td] [/tr] [/table] Code: [code][left]T h a n k s . L e t m e s e e , y e s , I t h i n k I ' v e g o t i t ![/left]

 

[Bjornboy81]

Did you enter the tuned frequency? If so, why did you go for 19.33Hz? Seems kind of low. It looks like the actual will be around 50, which seems a little high. I think optimal would be around 35, 37 ish.

my $0.02.

 

[VeipaCray]

See this page...

Subwoofer Enclosure Software

 

[MASantos]

Josh, sometimes the easier way is the simplest.

A sheet of paper, pencil and a scaled ruler will do wonders, believe me. Much faster than the time of turning the computer on!

My 0.02€

Manuel

 

[Joshatdot]

Quote:

Originally Posted by Bjornboy81 /img/forum/go_quote.gif Did you enter the tuned frequency? If so, why did you go for 19.33Hz? Seems kind of low. It looks like the actual will be around 50, which seems a little high. I think optimal would be around 35, 37 ish. my $0.02.

This is why...smooth smooth FREQ across the board

 

[Joshatdot]

Quote:

Originally Posted by VeipaCray /img/forum/go_quote.gif See this page... Subwoofer Enclosure Software

I used WinISD to design my box...but it does not tell me how to CUT the MDF.

 

[VeipaCray]

The first link on that page Blaubox will print the cutsheet for the MDF.

 

[Bjornboy81]

Quote:

Originally Posted by Joshatdot /img/forum/go_quote.gif This is why...smooth smooth FREQ across the board

Gotcha...guess it lookes a little more out than that by the numbers. Looks good though!

 

[keyid]

if you buying large sheets of mdf get the long straight edge, pencil & jigsaw. HomeDepot/Lowes will also cut your mdf sheets to any specified dimensions too.
The stuff cuts like butter. dont get mdf wet and wear breathing mask, the glue is holding the mdf is nasty. If you have a router its easy to make perfect circle cuts.
pm if you need more details.